Chevy Silverado
Ford Bronco
Ford F-250
Late Model 1979-New Ford Mustangs

What is the stock horsepower and torque on a 1991 Ford Bronco 5.8?

678

Top Answer
User Avatar
Wiki User
2006-04-13 19:26:34
2006-04-13 19:26:34

HP is 210@3800 and torque is 315@2800

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

The EX with the VTEC engine has 130 H.P. and 144 Lb Ft of torque.

User Avatar

225 horsepower at 4200 RPM and 300 lb/ft torque at 3200 RPM

User Avatar

The horsepower of a 1991 Chevrolet 454 cubic inch engine ranges between 240 horsepower and 350 horsepower the engine torque ranges between 700 pounds and 850 pounds.

User Avatar

I had a 1991 and it was rated at 225 horsepower at 4200 RPM and 300 ft-lbs torque at 3200 RPM from the factory , I believe the 1990 was the same

User Avatar

225 horsepower at 4200 RPM and 300 ft/ lbs torque at 3200 RPM

User Avatar

Peak hp 193.5 @ 4,500. Peak torque 214.5 @ 4,000. Bone stock numbers for a 92 5.7L TBI. It is the same setup.

User Avatar

Max. Torque:170@4000rpm. Max. Horsepower:255@2400rpm. that answer is backwards horsepower is 170 @4000rpm torque is 225 @2400rpm not 255

User Avatar

90 horsepower and 101 ft/lbs of torque

User Avatar

most Hayes or any other auto book will give you wiring diagrams some stock horsepower and torque quotes. actual numbers check consumer reports or a review website.

User Avatar

245 Horsepower @4400 rpm and 345 ft lb torque @2400 rpm

User Avatar

MY CAMARO STOCK 305 1991 HAD 170 HP 255 TORQUE YOURS SHOULD BE THE SAME WITH TBI LITTLE MORE FOR TPI

User Avatar

it has 170 hp at low rpms and 255 at 4,000 rpm

User Avatar

The curb weight of a 1991 Ford Bronco Eddie Bauer edition with a 5.8 liter V8 motor is 4,430 pounds. This weight is when the vehicle is empty.

User Avatar

what is the head torque sequence for a 1991 pathfinder

User Avatar

F22A1. SOHC NON VTECH. 2.2 liter I4 125-140 horsepower @ 145 ft/lbs torque

User Avatar

either 170hp or 200-230hp depending on transmission and exuast choices.

User Avatar

does a 1991 thunderbird torque converter have a drain plug

User Avatar

DX & LX 4 cylinders have 125 H.P. 145 lb/ft torque.=EX 4 cylinder has 130 H.P. and 144 lb/ft torque.==SE 4 cylinder has 140 H.P. and 150 lb/ft torque.=

User Avatar

( 192 ) degrees Fahrenheit for all the factory available engines in a 1991 Ford Bronco ( according to fordparts.com )

User Avatar

It has the 3800 V6 used from 1988-1991, so it will have 165 horsepower. Don't be fooled though, these cars are still fast, I've driven one. If you were wondering, it has 210 lb/ft of torque. =)

User Avatar

My 1991 Ford Mustang 5.0 L - LX - was rated at 225 horsepower at 4200 RPM and 300 ft-lbs torque at 3200 RPM ( that of course was the high output 5.0 L )

User Avatar

From what I have found out by looking on the internet, it is somewheres between 190 and 225hp rating with between 295 and 325 ft./lbs. of torque. It's a very strong motor and it is very easy to bump up that horsepower and torque rating without spending a whole lotta dough lol.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.