0
What is the three shafts in a gearbox fitted to a front wheel engine rear wheel drive?
Wiki User
∙ 7y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What are three shafts in a gearbox fitted to a front engine rear wheel drive vehicle?
Could be a PTO (Power Take Off) to operate accessories like a dump body or a snow plow.
What are the three shafts fitted to a front engine rear wheel drive vehicle?
They are called driveshafts, they transfer power to the rear wheels.
What part in a 02 Honda auto transmission does the drive shafts connect to?
gearbox
Will a 1987 318 engine work in a 1999 dodge durango if you changed the intake?
ant engine will work in the shell of any car as long as: - the engine fits the car's bonnet. - the drive shafts are compatible with the engine shafts. - the correct intakes are in place. - the correct exhaust outlets are in place. - the correct brackets and supports must be fitted
What boats are equipped with the V Drive?
There are no particular boats equipped with the V Drive, but a boat that is equipped with it usually has two drive shafts. The boat will also have a gearbox and propeller.
Definition of a hardy spicer coupling?
A hardy spicer is a universal coupling as found on vehicle drive shafts and they are fitted with needle bearings
Where is gearbox oil in gmc jimmy 1998?
the gearbox is most commonly known as the transmission. It is just under the cab. directly behind the engine. It is bolted the engine block with 6 bolts, behind the transmission is what is known as a transfer case on 4wd Jimmy's it is bolted to the transmission. 2wd models do not have a transfer case, and have a drive shaft that attaches directly to the transmission. 4wd models have two drive shafts, one going to each end of a vehicle.
How do you fit a new clutch on a Peugot 106 Mark 2?
To replace the clutch on a 106 you will need to remove the air box, battery, wheels and starter motor and disconnect the gear linkages. Before you remove the drive shafts drain the gearbox vie a 3/4 square drive plug located on the bottom of the gearbox (then remove the shafts). After this you will need to support the engine and remove the engine mount from the gearbox. Once this is done the electrical cables connectors and associated clips will have to removed from the gearbox. Once you are sure that there is nothing left fastened to the box remove the gearbox bolts including the bolt located under the engine that secures the front pipe to the engine/gearbox. The gearbox should then be removed by sliding it slightly to the N/S of the car to extract the input shaft from the crank and then lowering to the floor, The clutch is then visible and can be replaced ensuring that the clutch is tightened evenly and properly aligned using the appropriate aligning tool (sometimes supplied with the new clutch). Before refitting the gearbox it is always worth replacing the driveshaft oil seals on the gearbox as these can be a pain if they leak once the job is complete. Refit the box and reassemble the components in reverse order remembering to refill the box with fresh gearbox oil
How do you remove a Hyundai Getz gearbox?
Just swapped a 1.1 getz geabox a bit fidly but not too bad-remove front subframe pull out drive shafts disconnect steering and roll bar disconnect gear change and electrical plugs(2) undo gearbox mount drop engine slightly and support split gearbox away from engine and remove downwards it took me about 9 hours but I don't do this for a living regards Dave k
Can a 2002 jeep be towed on a dolly?
Only with drive shafts removed.Only with drive shafts removed.
What is the power train of a front wheel drive car?
The engine, transaxle and axles (half-shafts).
What is a function of the clutch in the vehicle?
The purpose of a clutch on a vehicle is to disconnect the drive of the engine from the gearbox (this would be required when the vehicle is stationary or to change gear). While the engine is running the crankshaft is continually turning, It is the crankshaft that turns the gearbox and via the gearbox the road wheels. Obviously there are times when the engine is running but drive is not required, The clutch is the mechanism by which this is achieved.
