0
What is the torque sequence and torque for the head bolts on a 1992 GMC 350 engine?
Wiki User
∙ 17y ago
Sorry 17 Bolts. You Should Have (16) Bolts Per Head. The Torque Should Be 65 FtPds. Torque In Three Equal Passes. Tighten All Bolts Till They Pull Down On The Head So They are Not Loose. Then Tighten The First Pass Say 25 lbs. Next Pass Bring Up To 45 lbs. then Last Pass Bring To 65. Looking At The Head Number The Bolts On a Sheet Of Paper This Way. Outside Bolts Next To Exh Manifold 16-12-8-4-3-7-11-15. Now In The Middle Row Number Them 17-9-(1)-6-14. Inside Row Number 13-5-2-10. Draw This Out Like Looking Down At The Head, Now You Have The Sequence. Best To You
Wiki User
∙ 17y ago
Add your answer:
Earn +20 pts
What is the torque and tightening sequence for the valve cover gasket for a 1992 for tempo 4 cylinder?
Torque for valve cover bolts is 7 to 10 ft. Lbs . Tighten the bolts in a criss-cross pattern .
What are the torque specs and torque sequence for a 1992 Nissan Maxima intake manifold?
what are the torque specs and sequence for a 1992 Nissan maxima manifold
What is the torque sequence and torque for head bolts on a 1992 Toyota Paseo?
you need a chiltons motor guide don't count on what someone on the computer tells you ..this has to be right or you just wasted a lot of money
What are the torque settings for a v8 3.9 land rover discovery 1992?
For the 3.9 head bolts (streach bolts) only use new bolts and follow this sequence: Tighten to 20nm in correct sequence. Then tighten each bolt 90 deg turn in correct sequence. Wait 15 minutes. Then tighten each bolt a further 90 deg turn in correct sequence. Done.
Torque sequence for 1992 geo prism?
For what part? You're too vague. Be specific.
What is the torque for head bolts on a 1992 Mercury Cougar?
Buy a Haynes manual because you have not given engine size and also you need to know the order of sequence in which to tighten them as you do not tighten them all the way first time. Usually you take 3 times around at 1/3rd recommended final torque ft/lbs, increases meaning the final or 3rd time you set the wrench at final torque specs.
What is the valve cover gasket torque sequence on a 1992 Toyota Previa?
35 foot pounds
What is the engine torque of a 1992 5.7 liter Buick roadmaster?
its a 350hp vortec engine.
How do you remove the tourqe converter bolts from a 1992 Nissan Pathfiner?
After you have removed the cover from the lower half of the torque converter housing and driveplate you can remove the four bolts that secure the torque converter to the driveplate. Remove them one at a time by rotating the engine so that each bolt comes into view at the bottom where you have removed the driveplate cover.
What is the hp and torque ratings on a 1992 300 cid Ford truck engine?
150 horsepower ,torque is unknown
What are the torque specifications for the water pump bolts on a 1992 Dodge Dakota?
For all 1992 Dodge Dakota V6 andV8 engines:All of the water pump bolts are to be torqued to 30 ft. lbs.For 1992 Dodge Dakota 4 cylinder engines:Upper bolts are torqued to 21 ft. lbs.Lower bolts are torqued to 40 ft. lbs.Waterpump housing-to-cover bolts are torqued to 105 inchlbs.
How much horsepower and torque did a stock 1992 chey 4.3L engine put out?
160 HP 235 lb/ft torque.
