Toyota Tundra

What is the torque specification on a 2001 Toyota tundra front oxygen sensor?

123

Top Answer
User Avatar
Wiki User
Answered
2014-08-28 16:42:42
2014-08-28 16:42:42

The 2001 Toyota Tundra front oxygen sensor torque specification is 20 pounds. The oxygen sensor bolts should be torqued in 10 pound intervals.

001
๐ŸŽƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Related Questions


The 1995 Toyota 3.0 liter engine main bearing torque specification is 160 pounds. The rod bearings torque specification is 120 pounds.



every car's sensor is 50 ft lbs for trucks and such it varies from 80-110 ft lbs. i would torque it to 55 to be on the safe size but no more because you dont want to strip the threads on your cat


The 1989 Toyota rod bearing torque specification is 150 pounds. You should torque the rod bearings bolt in 50 pound intervals.



The Toyota 20R engine crankshaft bolt torque specification is 150 pounds. The crankshaft bolts should be torqued in 50 pound intervals.


There is no torque specs. on that. Just make sure it's tight and be carefull not to brake it off.


The 1995 Toyota Tacoma thermostat housing torque specification is 40 pounds. The amount of torque on the thermostat housing bolts is not that important. You basically do not want to break the thermostat housing bolts.


I don't believe there is a specific torque specification! Once you install the crush sleeve and tighten the nut to the desired preload on your pinion bearings, your torque will be what it will be.


The Toyota Corolla 1.6 liter engine cylinder head bolt torque specification is 150 pounds. The head bolts should be torqued in 50 pound intervals.


The Toyota Corolla 1.8 liter engine rod bolt torque specification is 120 pounds. The bolts should be torqued in 40 pound intervals.


The Ford Ranger alternator bolt torque specification is dependent upon the year of the Ford Ranger. In general, the alternator bolt torque specification is 45 pounds.


The 1987 Kia 1.8 liter engine had bolt torque specification is 120 pounds. The camshaft bolt torque specification is 90 pounds.


The head bolt torque specification for your Toyota 3.0 liter engine is 150 pounds. The head bolts should be torqued in 50 pound intervals.


The 1999 Pontiac cylinder head gasket bolt torque specification is 160 pounds. The intake manifold bolt torque specification is 90 pounds.


The 2003 Chevrolet Suburban front axle hub as a torque specification of 120 pounds. You should never exceed the torque specification as you will cause the wheel seal to fail.


specification on gapping spark plugs for 2006 chevy cobalt


where is torque conversion sensor on my 1997 didge intrepid?


The torque specification, for the harmonic balancer on your 350 cubic inch engine, is 280 pounds per square inch. The torque specification may vary according to the manufacturer of the engine.



what is the torque specifications for the intake bolts on a ford 4.2L?



what is the wheel lug nut torque for 2010 toyota highalnder


On the front oxygen sensor( located on the exhuast manifold towards the front easily accessed from under the car.) you have to take it off with a oxygen sensor wrench. then you have to cut and attach the new 02 sensor to the old wires. Once that is done torque the new sensor down to 33 ft lbs. Your done!!


spark plug torque for a Toyota 2.4 is 95 inch/lbs



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.