0
What is the torque specs sequence for a 1997 Chevy Cavalier 4 cylinder 2.2 engine?
Wiki User
∙ 18y ago
The long bolts should be torqued to 46 lb ft plus an additional 90 degrees, and the short bolts should be torqued to 43 lb ft plus an additional 90 degrees. They should also be tightened in sequence starting with the rear center bolt first, and then the front center bolt. The correct sequence, starting with the left rear bolt and moving clockwise would be: 8-4-1-5-9-10-6-2-3-7.
Wiki User
∙ 18y ago
Add your answer:
Earn +20 pts
Cylinder head torque spec for 1989 Chevrolet Cavalier?
need to know which engine you have
What is the torque sequence of cylinder head of Isuzu c190 engine?
100ft lbs
What are the cylinder heads torque sequence for a Toyota 4y forklift engine?
headboltstork
What is torque on the head bolts 2002 Cavalier 2.2?
The 2002 Cavalier 2.2 liter engine cylinder head bolt torque specification is 120 pounds. The cylinder head bolts should be torqued in 40 pound intervals.
Cylinder Torque sequence 2000 Pontiac Montana SV6?
What is the Cylinder Torque sequence 2000 Pontiac Montana 3.4V6
Cylinder head torque sequence for a 1991 pathfinder?
what is the head torque sequence for a 1991 pathfinder
What is the head bolt torque specifications and sequence for a 1995 geo metro 3 cylinder engine?
valve seal possition
What is the torque sequence for a 18hp single cylinder Briggs and stratton engine horazontal shaft head?
The torque sequence for a single cylinder Briggs and Stratton engine horizontal shaft head is increments of 2's for hp and 1's for head bolts. That makes 11 head bolts for an 18 hp.
What are the torque spec for the head for 2001 Chevy cavalier 2.2?
The 2001 Chevy Cavalier 2.2 liter engine cylinder head bolt?ætorque specification is 120 pounds. The cylinder head bolts should be torqued in 40 pound intervals.
What is the Cylinder head bolt torque 2003 impala 3.4?
Torque Sequence ------------------------ Front | 5 3 2 8 | Of | 7 1 4 6 | Engine ------------------------- Step 1 - Torque to 44 ft/lbs Steps 2 - Turn 95 degrees Recheck final torque in sequence
1993 cavalier head bolt sequence?
This is for a four cylinder (most were) Torque sequence ------------ front | 8 4 1 5 9 | of | | engine | 7 3 2 6 10 | ------------ Step 1: torque long bolts 8,4,1,5, & 9 to 46 Ft/Lbs torque short bolts 7,3,2,6, & 10 to 43 Ft/Lbs Step 2: torque all bolts an additional 90 degrees Recheck final torque in sequence *** CAUTION *** engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque. This is for a six cylinder (One side at a time) Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION *** engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque. This is all pasted from Auto Zone's website. It's not really copyrighted I'm guessing because you can easily go into a store and they will print this off for you. Good Luck!!
What is the torque sequence for rocker arm bolts on a 1991 ford 1.9 engine?
There is no torque sequence just torque rocker arm studs to the proper torque
