0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Will an amp of 1400-watt with 700-watt rms blow a sub with 1100-watt peak and 600-watt rms?
nope your powering it just right
If you buy a two sub woofers with 400 Watt continuous and 1200 watt peak power how many watt amp should you buy?
800 watt should be fine
How many Watts Peak is one Kilo Watt of energy?
One kilowatt is 1000 Watts.
What does price per WP mean in solar power?
When used in the context of solar power, "Wp" means watt-peak. This refers to the nominal power of a solar cell or a solar panel. Watt-peak, kilowatt-peak, and megawatt-peak are often used interchangeably. Price per Wp refers to the amount of power that a solar cell or panel generates under real-life conditions in relation to its cost
Can a 200 watt amp power a 250 watt rms sub?
YES! it won't reach it's peak, but that's also probably a good thing, cause it'll be harder to blow your sub. i prefer to buy either the exact watt match for my subs and amp, or buy the next lower watt amp from my subs
Will a 1600 watt amp blow a 450 watt sub woofer?
Well, it depends. When you look at subwoofers, it will say RMS and peak. Now, let's talk about the "RMS" and "peak" on the subwoofer. The RMS is the real power. That's what were gonna be looking for. The RMS is the continuous power design for the subwoofer to operate. The peak is the maximum power the subwoofer can handle. Obviously, were not gonna be running the subwoofer with its peak power because that will decrease the life of your subwoofer. Running too much power or too little can damage your subwoofer. It's also important to run it by it's RMS rating. So, I don't know if that 450 watt is the RMS or peak. I'm assuming that it's the RMS. As long as you don't bridge it, it should be fine.
If you have a 300 watt RMS and 1000Watt peak power sub-woofer what rating of an amplifier should one consider using?
an amp with 300 or less rms wattage output and 1000 or less peak wattage output.
Why does 1000 watt amp go into protection mode on 2 speakers that have a 400 watt peak apiece?
nope most likely a ground check your ground and wires worst case check ground on body of amp with a screwdriver
What size amp do you need for 6 and a half Sony speakers that has 190 Watt peak power and 40 rms and Sony 6 by 9 speakers that has 300 Watt peak power and 60 rms?
200 RMS 4 channel or 2 channel so u know add the rms of the speakers to find the amp rms needed
In what terms are PC power supplies rated?
AT/ATX PC Power Supply Units (PSU) are typically rated in Watts. The Wattage Rating can be in Peak Wattage or Constant Wattage. Every Power Supply has a peak wattage and a constant wattage, but it isn't uncommon for only one or the other to be advertised and not both. Peak Wattage is how many amps the PSU can give out for a short period of time before overheating. The length of time a PSU can sustain this peak wattage is generally about 30-60 seconds. Constant Wattage is how many amps the PSU can give out nonstop. This number is always less than its Peak Wattage counterpart. Constant Wattage is usually (but not always) rated at 40c. For example, if we assume a 75% efficiency between peak and constant wattage, a PSU may be advertised at 500 Watts peak, but may only do 375 Watts constant. When compared to a 450 Watt constant PSU, the 500 Watt peak PSU might sound more powerful at first, but the 450 Watt constant PSU would be able to do 600 Watts peak.
Can a 1200 watt amp give good bass to 2 kicker cvr 12's?
It depends on the rms of the two cvrs combined. Also if the 1200 watt amp is 1200 watt rated (rms) or 1200 watt peak. Lets say the two kickers have an rms of 600 watt each, and the amp is 1200 watt rms, which it probably isnt but i'll pretend. This set up would work because 600 of the amps watts would be correctly matched with one sub, and the other 600 would go to the other sub.
What is the best amp for a 12 inch sony xplod 350W rated power and 1200W peak power?
1000-1200 watt peak amp its rated at 350RMS and breaks at 1200 watts so ether a 500-600RMS should do fine and sound killer
