0
What size bolt goes in the motor mount that bolts the bracket to it?
Wiki User
∙ 14y ago
it is the same size of the bolt same as the hole and thread. the higher the grade of the bolt the more touque you can apply.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What are the Motor mount bolt sizes on a 96 windstar 3.8?
The motor mount bolt size for a 1996 Windstar 3.8 is cross-thread a 3/8" bolt. That is the only bolts that will fit.
How to change motor mounts on a 1990 Dodge Caravan?
Place a hydraulic jack under the motor.. preferably between the trans and motor for replacement of front motor mount. Proceed to remove the bolts attached to the underside of radiator. Next remove the bolt between the mount. Total removal is 3 or 4 bolts? Make sure the jack is just resting under the transmission as to allow for the new mount to just slide in to the bracket in the same place it was removed. . I don't claim to be a mechanic.. just have had extensive dealings with all of my mounts. Just remember.. you don't have to remove the entire bracket.. of course unless it is broken. the bracket is in two pieces. you only remove the front bracket. Transmission mount. Remove the air filter box..disconnect all wires in your way. there is a bolt you can see under the drivers side wheel well. This bolt is located behind a rubber grommet. Remove the rubber and there is the bolt. This bolt loosens the transmission mount. I removed the entire bracket to replace mine. There are three bolts that are clearly visible under drivers side wheel well. These bolts have to be removed to take the bracket out. This took a little time to put back in... just be patient with all the mounts or you will be one frustrated individual.
Bolt size for Honda civic rear motor mount bolt?
What size bolt for a 2005 Honda civic DX power steering tank bracket..
How do you disassemble a motor mount on a 1997 Chevrolet cav?
If you are going to keep the bracket and just replace the original mount, then remove the mount from the car (take the overfill plastic coolant jug off 10mm bolt) then support car with jacks stands and engine with jack and piece of wood. Using a 15 mm socket remove the 7 bolts holding the bracket to the engine (2 are bolted the engine ) the top bracket comes off and there are 2-13 mm bolts under it. when you get it out of the car take a screw driver to the sides of the holes on the bottom of the bracket, because they are press fit to the motor mount. that is what i did today and then installed the new mount in reverse
Change engine mounts 93 jeep grand Cherokee 5.2 liter?
To replace the front motor mount: 1. Disconnect battery ground cable, then position fan to assure clearance for radiator top tank and hose. 2. Install suitable engine lifting fixture, then raise and support vehicle. 3. Remove engine support bracket through bolts 4. Using lifting fixture, slightly raise engine. 5. Remove engine mount bolts, then the mount. 6. Reverse procedure to install, noting the following: a. On right side, torque sill bracket to 40 ft.lbs. b. On left side, torque sill bracket 2 top bolts to 40 ft. lbs., 2 side bolts to 70 ft. lbs., and 2 bottom bolts to 89 ft. lbs. c. Torque mount to engine bolts to 65 ft. lbs. d. Torque through bolt to 48 ft. lbs. For the rear motor mount: 1. Disconnect battery ground cable, then raise vehicle and support transmission. 2. Remove nuts holding the clevis bracket to the cross member. 3. Raise the transmission slightly, then remove the through bolt and nut. 4. Set rear mount bracket clevis aside, then remove the bolts holding the rear mount bracket assembly to the transmission. 5. Remove the mount bracket assembly from the exhaust hanger. 6. Reverse procedures to install, noting the following: a. Torque mount bracket to transmission to 34 ft. lbs. and clevis bracket stud nuts to 30 ft. lbs. Torque through bolt to 48 ft. lbs.
How do you replace serpentine belt on 1996 Pontiac Bonneville?
if its the one im thinkin you are talkin about ,theres a spacer on one of the bottom bolts that comes out after you that the bolt out. then the belt slips through the space, so you dont have to take off the motor mount bracket.
In an 1991 olds 98 do you have to remove the engine and engine mount to get the bottom bolt in when installing a new water pump?
Noyou don't. I just changed my water pump in a 91 olds 98 3.8 liter. This is the way I did it. Put car on ramps or jacks stands. There is two bolts under the motor mount that you need to loosen but not take out. Then jack the engine up to the bar that goes across. Then take out the bolts that hold the motor mount on the top. Once you hav e done this then remove the belt. There are three bolts that hold the bracket, Take them off. Oh, i forgot there is a bolt that goes through the motor mount take it ot before you take the bolts out on top that hold the motor mount. Once you get the bracket off then the water pump is exposed for your taking. You will have to put the belt back on to loosen the bolts that hold the pully. that is pretty much it. Make sure you use something to lube the bolts because mine were rusted and din't want to losen especially the bottom to bolts that hold the motor mount. once I got the bracket off it only took 15 min. to take off clean and put other one back on. It is not hard but it saved me $150 to do it myself. Part was only &25 lifetime warranty. have fun. if you need further help you can send me an email at nphantom66@yahoo.com
How do you change the motor mount front and rear on 1991 Chevrolet Corsica?
Loosen the motor mount retaining bolt. Jack the motor up a few inches. Remove the motor mount retaining bolt and the motor mount bushing. Reverse the process to install the new motor mount.
What size scres to mount toshiba model 37hl67s to wall mount?
Most brackets today come with all possible bolt sizes for your range of TV sizes. It will be either a 6mm or 8mm bolt. Just try the bolts from the hardware pack when you buy your bracket.
How do you install a motor mount on a 1996 Chevrolet Corsica?
Put the new motor mount bushing into the appropriate place. Put the motor mount retaining bolt in. Let the engine down from the jack. Tighten the motor mount bolt.
How do you replace the Mazda 626 motor mounts?
Each motor mount is held in place by a retaining bolt. The retaining bolt goes through the middle of the motor mount. Remove the retaining bolt. Jack the engine up. Replace the motor mount.
How do you replace a rear motor mount on a 1995 Toyota Corolla?
Lift vehicle high enough, remove mount bolt, crossmember bolts supporting it with jack and lower to create room for removel of mount,
