0
What size mower deck belt goes on a Ford LT 12 H with a 42 deck?
Wiki User
∙ 12y ago
Most LT12H mowers take a #213676 OEM belt or #6885 Gates belt for the blade application
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Where can you see a drawing of how a deck belt goes on a model 3410 with 42 inch deck?
You will need to order a manual on the mower from the manufacturer (I assume Simplicity).
How do i Change belt for blades Murray riding mower model 40907X20A?
I changed the blade belt on my Murray mower. Now one blade stops and goes. If I lower the deck the blade stop . What did I do wrong?
Where can you see a drawing of how a deck belt goes on a model 5200 Simplicity riding tractor mower?
I have the information if you want to give me a call. 989-871-4227
Why does your mower blade keep running when out of gear?
the main thing is that your belt that goes from the deck to the pulley beneath the pulley on the engine that makes the mower move there is a pulley below that and the belt is to tight. that is the only thing i can think of. hope this helps
What size mower deck goes on a john deere 111?
38'' deck
Where can you find a Drive belt diagram for your MTD 13AS699H062 mower?
It would be the "H" deck at the link below; the various 46" decks it would be the first one shown and the top belt goes to the top pulleys on each on each side(not shown.)
How do you route mower deck belt on a simplicity 4212?
goes around the engine pulley next both deck (blade pulleys) then put it around the tightener (blade engagement pulley) with the back Flat side of the belt against the pulley. make sure all the belt gaurds do not contact the belt with the blade engaged or dis-engaged. when you are installing the belt you will have to disconnect the deck lift rod to get the belt the other side of it or it will rub and ruin it. should be just a matter of pulling a cotter pin or push pin.
What size belt goes on a Murray Riding Lawn Mower - 12.5 HP 40 Cut Lawnmower?
what size belt do i need with a murray riding lawn mower that is a 12.5hp. 40"
How do you change the lawnmower belt on a ford LT 12 H?
First, I am not a professional and leave you responsible for safety. Remove the old belt... it's good to take note of were it goes but if you can't no worries. If you have a cover on the mower deck that goes over the pulley you will need to remove it... I think it's only 3 screws. Hook the new belt over the pulley (make sure it seats in the groove nicely. Pull the remaining slack of the belt toward the front. You'll notice 2 pulley's in the front that turn up. Both grooved. You'll need to open the cover on the tractor and you'll see on the front on the engine there are 2 pulley's on a clutch. Youll need to seat the belt into the 2 grooved pulleys that turn up (notice one is on a spring and pulls back when pressure is applied.) then push it on the engine pulley. (Use the appropriate one to your belt and mower deck configuration.) You'll probably have to start it and then turn the pulley (again on a clutch so should rotate easily) to get it to feed on. (Also, it will turn the blades on the mower deck so be really careful of what/who is near them.) That should be it. If you really have a tough time and your sure it's the right belt then you can unhook the deck and slide it forward to put the belt on... then the struggle is to hook the deck back on. but some people do find this easier (since the belt won't pull as much since it's all the way in the grooves. By the way... what size belt is it? (I have an LT12 and it didn't have a belt on it... took my best guess but not positive its the right size.)
How do you change a belt on a John Deere L118?
To change the mower deck belt; Lower the deck to it's lowest position. Remove the mower deck by pulling the two pins on either side at the rear of the deck. Remove the pin holding the front of the deck. Remove the belt from the drive pulley under the engine. Slide the deck out from under the chassis. Remove three bolts holding the plastic shroud on the left blade pulley. Make a note of how the belt wraps all pulleys and idlers. You can now replace the belt and follow the above steps in reverse order to replace the mower deck.
What size primary belt for ranch king pro 22HP 46 inch?
Ranch King is a brand name of the manufacturer MTD. Product manuals with part blow-up diagrams are available from MTD's web site, http://www.mtdproducts.com/ Models are identified from the model number printed on a label under the mower seat. Parts can be ordered directly from MTD or other distributors on the web. It is my experience that original brand name MTD belts work best. The 22HP, 46" mower deck Ranch King Pro has 3 belts: The drive belt which runs from the engine pulley back to the hydro drive unit to provide over-the-ground propulsion is part #754-0349. A mower has either an electric PTO or a manual PTO, not both. The electric PTO belt the provides power to the blade deck (runs around the electric clutch on the engine shaft (activated by electric switch, not the mechanical hand lever that engages the mower deck) is p/n 754-0476 for the 46" deck. The manual PTO belt the provides power to the blade deck (runs off the pulley on the engine shaft (activated the mechanical hand lever to the left of the steering wheel that engages the mower deck) is p/n 754-0228 for the 46" deck. The deck belt that goes around the 3 blade spindle assemblies on the mower deck, to drive the grass cutting blades is p/n 754-0349 In my experience, the PTO belt lasts about half a season, the other belts break about every other season when mowing 4 acres weekly.
Does belt go inside or outside guide pins?
On a riding lawn mower, the drive belt(s) goes inside the guide pins.
