0
What size socket do you need for a pulley to ease the tension to put in a alternator belt on a 2007 ford fusion?
Wiki User
∙ 9y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How o you replace alterntor on 1998 Pontiac bonnevile se?
first disconnect the battery - use a long breaker bar and socket to take tension off the tension pulley and at the same time remove the belt from the alternator pulley. disconnect the wires to the alternator make note of their positions. Then remove the 3 mounting bolts from the alternator.
How do you loosen serpentine belt tension on a 2000 s10?
Tensioner pulley below the alternator. Should be a 14 or 15mm socket and turn counter-clockwise.
How do you loosen the alternator belt on a 2000 Pontiac grand am?
there is an idle tension pulley on this motor that u either use a socket or just the head of a 3/8 drive rachet and pull
How do you take the tension off of the serpentine belt on a 1996 Chevy Corsica?
On my 94, the tension bar is between the passenger wheel well and the motor, towards the bottom. Use a wrench to lift the tension bar, and the belt should loosen up. On my 95 Corsica 2.2 4cyl, the tension pulley is DOWN and to the LEFT of the alternator pulley. The space in between the bolt on the pulley and the side of the engine compartment is to small for a socket. I used a box wrench and turned CLOCKWISE.
How do you replace the serpentine belt tension pulley on a Buick Regal?
with a 9/16 socket and ratchet
How do you replace a serpentine belt on a 2003 corolla?
a 19mm socket,breaker bar to tensioner and release tension by applying force towards the front of the vehicle. remove the belt from the alternator pulley. this will also be the last pulley for easier installation. it will save you a headache if you make yourself a diagram.
What do you need to loosen to change the serpentine belt on a 4 cylinder 1998 jeep wrangler?
u need to relaese tension on the tension pulley. this is usually done with a long socket wrench handle. when u release tension and remove belt you then release tension on pulley until you have routed new belt . you then move tension pulley again until you can put belt on it, then release pulley and it will automatically provide correct tension
How do you replace the alternator on a 1995 Chevy Tahoe?
The first thing to do is disconnect the battery from the truck. Then you will need to lossen the belt off the enginge. In order to go that their should be a tension puller on the front that a simple rachet and socket will do. you turn that till it lossens the belt and slide it off the alternator. If it doesn't have tension pulley then the alternator has a bolt that you lossen it to get the belt off. After you get the belt off you need to dissconect the wires on the back of the alternator then you can take the two bolts out of the alternator and simple pull it off.
How to change the serpenten belt on a 94 Buick LaSabre?
Hey there. There is a tensioner pulley just to the left of the alternator and a little below it.it has a bolt in the middle that if you put a large socket on it and crank it counterclockwise until it lifts upward and relieves tension on the belt you then (while you are still cranking on tension pulley ) just slide the belt off of the alternatoer and other pulleys . ..
How do you get to the tension pulley in a 1995 Pontiac Grand Am?
with the correct type of socket and bar for easy access I had to use a crow bar as a socket wouldn't fit.
How do you replace the serpentine belt on 1992 Buick Century 3.3l?
pull the tensioner to relieve the tension and slip the belt over the alternator pulley. The tensioner is a spring-loaded pulley below the alternator. The tensioner takes a special tool that fits into a square hole in the side of it. Or you can use an 18 mm socket on the tensioner's pulley bolt. Follow the decal near the right front corner of the engine compartment to route the new belt.
Where can you find installation instructions for the alternator on a 97 GMC Sierra?
If you buy a new alternator there should be instructions included in the box, but if not and I remember correctly all you have to do is take the belt off, and then there are just 4 bolts (1 on each corner) holding the alternator on.AnswerYou can look in any chiltons or haynes manual for removal and installation for this procedure. glynn hawleycincinnati, ohI have just recently changed my alternator on my 97 GMC K1500 truck. First off there are two types of alternator selections. With or without a black plastic cap on the back of the alternator. The most common is with the cap. Generally the alternators without the cap on the back are used for commericial vechiles. The first thing you need to do is to disconnect the battery, negative first always. then the positive. Once that is done you need to release the tension on the belt. Directly below the alternator there is a tension pulley that you need move to release the tension. I have found that a socket wrench without a socket works nicely. On the tension pulley there is a square indentation the socket fits nicely into that, then all you have to do is push down to release tension to slip the belt off the alternator. Once that's done remove the bolts holding the alternator in place, mine only had two bolts. Once those are removed there are two wires that need to be taken off. One is connected to the positive cable of the battery and connects to the back of the alternator witha simple bolt. The other wire is a plug with a clip that you just pop off. Easy enough...get new alternator an reverse these steps..reconnect all wires to alternator, bolt in place. Bring tension pulley back up with socket wrench to slip the belt back on the alternator. Reconnect battery cables and your home free.......Charles in Indy
