0
valve spring compresser
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
How do you remove the valves in a 2000 model Daewoo Nubira?
dermining the differences between valvesHi there champ, i am just surfing myself on this site but i can answear this question for you. this all depends on how the valves sit inside the head cylinder, you have two different types of valves which is, 1} insinked valves 2} standard valves. to determine the differences between the two, the insinked valves are valves that have been sinked inside and into the engine head cylinder, the steps down below follow for non insinked valves inside the head cylinder. for normal valves you can buy a tool from a spare part shop to take the standard valves out but if you have insinked you need a machine to take them out but if you go like i did to a head specialist they could do it for you and put them back in because the have a hydralic/air compressor that does the job. ok!1.step= take the rocker cover off. 2.step= take the cam shaft off. (TAKE NOTE PLEASE : the timing belt will have to come of aswell) 3.step= (if over head cam) remove caps from the top of valves. 4.step= remove the head from engine. 5.step= remove the valves with the valve remover tool purchase from any spare part shop. as mentioned before if they are INSINKED you will have to compress them out.that should answear your question to the finest detail that i can put it for you.
How do you determine if the head is damaged on a interference engine 2.0L Plymouth breeze?
You need a tool called a cylinder leakage tester. You remove the spark plugs and rocker arms, install the tool, and pressurize the cylinders to check for damaged valves.The other options are to install a new timing belt and try to start the engine, or remove the head and visually inspect.You need a tool called a cylinder leakage tester. You remove the spark plugs and rocker arms, install the tool, and pressurize the cylinders to check for damaged valves.The other options are to install a new timing belt and try to start the engine, or remove the head and visually inspect.
How do you replace the ignition lock cylinder on 93 Chevy 3500?
Pull the steering wheel with a puller tool, remove the lockplate with a lockplate tool, remove the turn signal assembly, remove the hazzard switch, remove the brass connector, remove the lock cylinder.
Cracked cylinder head but passes for no leaks detected just serface crackstress crack between valves should i have the crack repaired or not woorie about it and hope the crack will not spread.?
have the head repaired it will get worce check leakage into coolent with a gas detecter tool. but do get it repaired.
What is meant by a valve spring compressor?
A valve spring compressor is used to remove collets in a car. The tool compresses the valve springs in the cylinder head of the car allowing the collets to be removed.
How do you replace the valves on a 92 Ford Ranger?
many of the accesories must be removed first, remove the head per repair manual and take the head into a local machine shop that performs head jobs. They will check the head for cracks, pressure test it and insure the head is still flat. If you want to do it yourself, get the gasket kit, buy the valve removal tool, new valves and install them. with out reaming the guides though there is a chance the valve stems will still leak.
How do you replace valve seals on a 1995 Eagle Talon?
You can do it on the car by pumping compressed air in to the cylinder (must be at TDC). The compressed air will keep the valves pushed up while you remove the valve springs. The downside to this that you will have to have a special tool to compress the valve springs to remove the keepers and you can only do 1 cylinder at a time because each piston must be at top dead center.
What tool measures a graduated cylinder?
Graduated cylinder is a tool to measure volumes.
What is the procedure for grinding valves on a 185 Honda trx?
If you are not sure, and do not have the tool's, it would be best to take the head and valves to a shop to have it done. Believe me, if the valves are not ground to the specific degree, and angle, all your work will be for nothing, and the engine will not run.
How do I set the Distributor on the motor for a Chevy pickup truck year 1989?
Remove the #1 spark plug Remove valve cover Rotate engine manually (make sure in neutral if std.) until #1 piston is at the top of the cylinder (check with dowel or similar tool) and both intake and exhaust valves are closed. This is TDC Install distributor so that the rotor is firing at No. 1 cylinder
Where is the slave cylinder on a 2002 Chevrolet S10?
It is on the fire wall close to the master cylinder, and it is small. Whoever wrote this is totally wrong very wrong the clucth slave cylinder is located inside the transmission you need to remove the transmission and that is the only way to replace slave cylinder because you have to slide out the cylinder from the input shaft after you remove the mounting screws also there is a trick to remove the Hydrolic line you can use special tool or use two flat head screw drivers put each on both side and push toward transmission and have a friend pull out the line anyway special tool only cost like $5.00 and good luck
Do you have to remove the valve cover to replace the spark plugs on a 2001 Mitsubishi galant 4 cylinder?
No, you do need a long socket extension that will not release the sparkplug socket deep within the cylinder head. Mine releases with a button at the top of the extension. I'm not sure what the technical name for the tool is.
