0
What two precautions should be taken when hitting the cold chisel with a hammer?
Wiki User
∙ 11y ago
Make sure the hammer actually hits the end of the chisel, not your hand. Make sure the pointed end of the chisel is held firmly against what you wish to break or move.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
How do you remove the lighter in a 2004 2500 series Silverado?
try using your teeth, if that dont work a hammer and chisel should take care of it.
How can you avoid hitting your fingers when driving in a nail with a hammer?
You should practice hitting the nail very slowly but with force. You cold also try wearing gloves for the extra protection.
My 1995 Ford Fiesta doesn't start?
If you try hitting the starter with a hammer it should get it turning again..if its not that,its your battery or plugs.. Regards, Michael,
Chevy blazer 99 front door panel removal?
i think you should remove the door first then remove the door panel by hitting it with a soft hammer to release it.
What precautions should you take when preparing food?
Wha precautions should you take when preparing food
How to take down bathroom tiles?
I would get a thin chisel and at an angle tap with a hammer and remove the grout from around one tile. Use a wide tipped chisel and gently work your way under the tile at all sides until it comes off.When the first tile is removed use a wide tipped chisel and put under the tiles to be removed. Tap with a hammer underneath the tiles they should come off pretty easily.( Make sure not to dig into the (sheetrock) wall with the chisel).This is what I would do. Do it at your own RISK!I just got finished doing this today but the tiles were set onto concrete. You'll have to use a lot more muscle and Definitely wear protective eyeglasses for all jobs that you are striking one object to another.
How do you remove a front axle assembly on an Acura Vigor?
To remove the driver side cv axle: place a large flathead screwdriver between the transaxle housing and the axle. Then place a chisel behind the screwdriver. The order will be: transaxle housing, chisel, flat screwdriver, axle. Then give the chisel a hit or two with a hammer and it should pop out with ease. I'm not sure about the passenger side axle but I think you may have to take off the pillow block that is bolted to the transaxle which the cv axle sits in.
What are 4 precautions that should be followed in your PE class?
There are no precautions. HA HA HA
How do you demagnetize a apir of tweezers that somehow became magnetized?
A sharp blow with a hammer should do the trick. The atoms in the tweezers are all alligned north/south, hitting them should dealign the atoms and therefore demagnetize the tweezers. Be carefull not to damage the tweezers!!!
Where do you get the chisel sims 2 castaways Im so stuck and the walkthrus are no use to me. Any ideas?
What system If wii or ps2 just go to the work bench and select tools and chisel should be there If DS the chief Gives you the chisel
What tools are needed to cut or slice a geode?
You can use a chisel and hammer. For a nicer finished product, get a brick saw that uses water to clean and keep the rock cool while cutting. You will need to make a holder for the geodes because they come in a variety of shapes and sizes. When cut in half they should be ready for presentation with little more polishing and cleaning to do. As always, use proper safety precautions such as gloves and glasses and if you are not familiar with how to operate a wet saw, ask an adult or professional.
What is a chisel made out of?
Handles are made of all sorts of shapes and sizes, and of many kinds of wood. The cheaper grades of file handles are made of soft wood. Chisel handles should always be made of hard wood. Apple wood is often used for firmer chisel handles. Socket chisel handles for heavy work are often made from hickory.ANS 2 -Many of my favorite wood chisels have handles made from 'easy to grip' rubberised composite materials. Most of these have the tang of the steel carried right through to the end of the grip. This enables the user to hammer if he really needs to ( on the odd occasion I do that, I always use a 'dead-blow' hammer.)
