0
What type of meter would be connected on both sides to a resistor in a current?
Wiki User
∙ 7y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Can a magnet slow down an electric meter?
Yes, definately yes. The Magnet will pull the spinning disk on the electricity meter resulting for that disk to slow down and THE RESULT OF MONTHLY ELECTRICITY BILL will decrease 25%. Just place the magnet on both sides of the Electricity Meter then It will slow down. WARNING: Do not get caught by the Readers or you will busted for jail! WORKS ON ME! :D
Why the current is the same in both sides of the main line that connects the voltage source to the parallel branches.?
Because... in a parallel circuit - assuming the wires are all of the same material, the current splits equally at the dividing point.
How much is cft in cbm?
There are 35.314 CFT (Cubic Feet) in 1 CBM (Cubic Meter). So, if you have CFT, divide by 35.314 to get CBM. If you have CBM, multiply by 35.314 to get CUFT. There are 3.2808399 feet in 1 meter. Cubic means 3 sides, so 3.2808399 * 3.2808399 * 3.2808399 = 35.314.
Does a transformer boost electric energy?
The transformer doesn't "boost" energy. If the voltage on the output side is higher than the voltage on the input side, then the current is lower. The power (energy every second) on either side is the product of (voltage) times (current), and that product is the same on both sides of the transformer.
1 cubic meter equals?
The cubic meter, symbol: m³, is the SI derived unit of volume. It is the volume of a cube with edges one meter in length. 1 cubic metre is equivalent to:1,000 litres = exactly~35.3 cubic feet (approximately)1 cu ft = 0.028316846 m³ = exactly~1.31 cubic yards (approximately)1 cu yd = 0.764554857 m³ = exactly~6.29 oil barrels (approximately)1 oil bbl = 0.158987294 m³ = exactlyA cubic meter of pure water at the temperature of maximum density (3.98 °C) and standard atmospheric pressure (101.325 kPa) has a mass of 1000 kg, or one tonne.
How do you install a resistor in an DC circuit?
It depends on the purpose for installing the resistor. If the intent is to decrease current flow, the resistor must be connected in series with the load. If the purpose is to increase current flow, the resistor must be connected in parallel with the load. To connect a resistor in series, connect the resistor to one side of the power source, in line with the load. This will decrease circuit current flow. To connect a resistor in parallel, connect the resistor between the positive and negative sides of the power source, which will effectively connect the resistor across the load . This will increase current flow through the circuit. However, before connecting a component in parallel, make sure the increase in current flow will not exceed the current rating of the circuit or fuses/breakers will blow.
What type of meter would be connected on both sides of a resistor in a circuit?
ammeter in series at any side as required since it is bilateral and voltmeter is connected in parallel to measure voltage drop across it
Can a resistor be installed backwards?
Resistors can be installed in any direction in a circuit. It doesn't matter in which direction you are installing a resistor. Resistor will resist the current in both sides of the connection. You can also apply capacitor in any direction for alternating current. Where as if you are concerned with direct current, a direction is needed to apply the connection
Is a resistor bilateral element?
Yes, a resistor has two sides, and furthermore they are interchangeable.
How do you test blower motor resistor on a Dodge 2005 Grand Caravan?
Resistor is behind glove box (Push inward on glove box hinges to release) Pull out both sets of wires from resistor plug-in. (push release clips on both sets to pull out wires) Remove 2 small screws holding the resistor. Remove the resistor ( test the wire that has the small diode ) with a multimeter to ensure it has power on both sides of the diode. If there is current on your multmeter the resistor is okay...... if no current is present on your multimeter the diode is burnt and the resistor unit needs replacement.
Why does one trace of the oscilloscope traces have to be inverted to display the voltage and current with the correct phase relationship?
One trace of the oscilloscope traces have to be inverted to display the voltage and current with the correct phase relationship because you are probably connecting to both sides of a small resistor in series with the load. The supply side shows voltage, while the load side shows voltage drop for the load. You are showing differential voltage across the resistor in the second trace and, of course, its negative.If, however, you are using a current probe, perhaps a clamp-on ammeter, I would question if you have it connected correctly.
How would a three phase meter reading compare to three single phase meters connected to the same service?
The reading on the 3-ph meter would equal the sum of the three separate readings on the single-phase meters. The neutral sides of the single phase meters do not need to be connected to the neutral wire as long as they are connected together.
Why doesn't current decrease in series resistance circuit though resistance opposes current?
If you add another resistor or just increase the resistance the current will decrease. I think the statement you are talking about means that whatever the current is in the series circuit it will be the same everywhere in that circuit, on both sides of the resistance. The resistance lowers the current in the entire circuit, not just after the resistance.
What formula would be used to find the maximum current that can be carried by a resistor if the resistor's resistance and wattage rating are known?
You use a combination of Ohm's law ( V = I * R ) and the power formula ( P = V * I ).Substituting you get: P = ( I * R ) * I = I**2 * RDividing both sides by R you get: P / R = I**2 * R / R = I**2Taking the square root of both sides you get: SQRT( P / R) = ISwapping sides of the equals sign you get: I = SQRT( P / R )Thus the maximum current can be found using the equation I = SQRT( P / R ).
Why don't capacitor discharge completely in an RC circuit?
Capacitors do not get "full" like a glass of water. The current into a capacitor is the rate of change of charge, so it's equal to C * dV/dt or something. If the voltage is constant, there's no current. If the voltage on both sides of the resistor is the same, there's no current through the resistor and hence into the capacitor, so that's the steady-state - what you call "full" - the capacitor charged to the supply voltage.
What does it mean to have closed polygons?
All sides are connected and there are no curved sides.
How many sides are there in a cubic meter?
If anything is "cubic" it must have 6 sides
