0
What type of screwdiver is used ot remove screws from the side panel?
Wiki User
∙ 14y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you remove passenger side kick panel on a 2000 expedition?
Using a screwdriver, remove the screws and clips from the panel. Pull the panel away slowly, remove wiring connections and the panel will come free.Ê
How do you remove a side panel on an eclipse?
Use the right sized screw driver, remove the screws and clips from the panel of the car. Pull the panel from the frame, and remove the wiring connections, and the panel should come off.
How do you remove the 2002 Montero subwoofer in the trunk area on the left side?
You have to remove the panels beginning with the upper panel. There are some screws holding in the grab bar and the storage cover holder but the rest are clips. You will after removing the upper panel, you will see some screws holding the lower panel. Remove the screws and then remove the carpet area in the rear left side. You will see some more screws. After that, remove the rear door molding and gently pry the lower panel back. You will then see the amp and the subwoofer.
How do you remove the battery from a 1990 Corvette?
You need to remove the small vented side panel. or at least remove the 3 screws from the wheel well and the one on the top of the panel. Then pull the panel out enought to remove the battery
How do you install a new headlight switch on a 1974 super beetle?
remove little plastic tabs on both side of switch panel. under will be 2 screws on each side. remove screws. pull out panel with switches press tabs to release switch.
How to remove drives side door panel 2001 corvette?
Use the right sized screwdriver, remove the screws and panels from the door panel and pull the panel away. Remove the wiring connections, and the panel should come free.
Where is the fuel pump relay on a 1994 corvette?
The fuel pump relay is located under the dash on the passenger side. You will have to remove the lower dash panel. Start by removing the air/heat vent by popping the center of the vent out and there will be two screws (Torques head) holding the vent in place, once the screws are removed the vent will pop out. Remove the side panel around and covering the fuses open and remove the fuse panel door you will see three screws that hold the side panel under the side panel there are two screws. After the side panel and the two screws are removed there are three nuts (10mm) where the air/heat vent was once removed the under dash panel can be removed carefully. Once the panel is loose disconnect the light and the panel can be set aside, you will see a small black box you will have to remove the cover and it does not tell you which one of the relays is the fuel pump relay. Good Luck.
How do you remove the stock radio of a 2004 Cavalier?
1) Open the glove box and remove 5 screws. I think 9/32" screws.2) Remove side panels from driver side dash and passengers side dash, and extract 1 screw from each side.3) Remove 1 Phillips head screw at top center of air vent.4) Extract 2 screws under vent panel, carefully remove top dash.5) Extract 3 screws from the top of the front dash panel, disconnect and remove radio.
How do you replace the driver's side mirror on a 1997 Chevy Cavalier?
Remove the dppr panel and there are screws on the inside.
Where is the fuse box on a 1986 Mercury Grand Marquis?
there is a panel below the steering column. there are two screws at the bottom of the panel and on each side. remove those two screws and the panel will lift from the clips on top . the fuse panel is then exposed.
How do you remove the door panel on your 2003 galant?
remove all screws, one is located in door handle, two are on the left side, one in the side holder, and one on the right side.Pull on panel until it pops out..
How do you remove radio in a 2008 ford f250?
Remove the two vents, also remove the cigarette lighter on the on side, and then the panel on the other. You will then see two screws from the two panels you just removed, remove those screws and then carefully pull the whole panel off. You will then see four screws holding the radio in. This should get you what you want.
