0
What uses a double ring of multimode or single-mode fiber to transmit data at speeds of 100 Mbps?
Wiki User
∙ 11y ago
FDDI
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What is double cage rotor and deep bar cage rotor?
deep bars in the rotor that result in higher rotor resistance at low speeds thus resulting in larger starting torques. The higher resistance is due to the skin effect.
What are the types of speeds used in aviation?
G's are used
What are the two characteristics of peer-to-peer?
The ability to get a virus easily, and speeds are slower.
What are creep speeds in cranes?
is minute slipping( creepin) of cranes permitted & accepted by regulation
Which wireless networking radio frequency yields faster speeds but offers shorter range?
5Ghz
Which two cable types are composed of glass fibers that can span the longest distances as well as provide high bandwidth speeds?
multimode fiber optic and singlemode fiber optic cables
Can you use multimode SFP in place of single mode SFP?
Singlemode fiber has a lower power loss characteristic than multimode fiber, which means light can travel longer distances through it than it can through multimode fiber. Not surprising, the optics required to drive singlemode fiber are more expensive. When to use each: Both singlemode and modern multimode fiber can handle 10G speeds. The most important thing to consider is the distance requirement. Within a data center, it's typical to use multimode which can get you 300-400 meters. If you have very long runs or are connecting over longer distance, single mode can get you 10km, 40km, 80km, and even farther - you just need to use the appropriate optic for the distance required, and again, the prices go up accordingly. Compatibility issues: They are not compatible. You cannot mix multimode and singlemode fiber between two endpoints. The optics are not compatible either.
What are wireless router speeds?
Wireless router speeds measure the amount of data that the router can transmit per second. The higher the speed the quicker the data can be transmitted.
How does the presence of myelin help axons work?
Myelin makes it easier for acons to transmit signals- it speeds there work.
What is the speed of human mind?
The speed of the human mind is difficult to quantify as it can vary depending on the task at hand. Neurons in the brain can transmit information at speeds of up to 120 meters per second, but cognitive processes involve a complex interplay of neural networks that operate at different speeds.
What is the difference between dual fiber single mode and dual fiber multi mode?
There are 2 major differences one color code. single mode will be white or yellow. multimode will be black or tan. 2nd the hole in the connector ferrel for the fiber. fiber is 125 microns. in a single mode connector the opening is 126 microns. multimode is 127/128.Single Mode cable is a single strand (most applications use 2 fibers) of glass fiber with a diameter of 8.3 to 10 microns that has one mode of transmission. Single Mode Fiber with a relatively narrow diameter, through which only one mode will propagate typically 1310 or 1550nm. Carries higher bandwidth than multimode fiber, but requires a light source with a narrow spectral width. Synonyms mono-mode optical fiber, single-mode fiber, single-mode optical waveguide, uni-mode fiber.Single Modem fiber is used in many applications where data is sent at multi-frequency (WDM Wave-Division-Multiplexing) so only one cable is needed - (single-mode on one single fiber)Single-mode fiber gives you a higher transmission rate and up to 50 times more distance than multimode, but it also costs more. Single-mode fiber has a much smaller core than multimode. The small core and single light-wave virtually eliminate any distortion that could result from overlapping light pulses, providing the least signal attenuation and the highest transmission speeds of any fiber cable type.Single-mode optical fiber is an optical fiber in which only the lowest order bound mode can propagate at the wavelength of interest typically 1300 to 1320nm.Multi-Mode cable has a little bit bigger diameter, with a common diameters in the 50-to-100 micron range for the light carry component (in the US the most common size is 62.5um). Most applications in which Multi-mode fiber is used, 2 fibers are used (WDM is not normally used on multi-mode fiber). POF is a newer plastic-based cable which promises performance similar to glass cable on very short runs, but at a lower cost.Multimode fiber gives you high bandwidth at high speeds (10 to 100MBS - Gigabit to 275m to 2km) over medium distances. Light waves are dispersed into numerous paths, or modes, as they travel through the cable's core typically 850 or 1300nm. Typical multimode fiber core diameters are 50, 62.5, and 100 micrometers. However, in long cable runs (greater than 3000 feet [914.4 meters), multiple paths of light can cause signal distortion at the receiving end, resulting in an unclear and incomplete data transmission so designers now call for single mode fiber in new applications using Gigabit and beyond.More Information:Multimode and Singlemode fiber are the five types of fiber in common use. Both fibers are 125 microns in outside diameter - a micron is one one-millionth of a meter & 125 microns is 0.005 inches- a bit larger than the typical human hair. Multimode fiber has light travelling in the core in lots of rays, called modes. It's a bigger core (always 62.5 microns, but sometimes 50 microns) & is used with LED sources at wavelengths of 850 & 1300 nm for slower local area networks (LANs) & lasers at 850 & 1310 nm for networks jogging at gigabits per second or more. Singlemode fiber has a much smaller core, only about 9 microns, so that the light travels in one ray. It is used for telephony & CATV with laser sources at 1300 & 1550 nm. Plastic Optical Fiber (POF) is large core (about 1mm) fiber that can only be used for short, low speed networks.Step index multimode was the first fiber design but is slow for most makes use of, due to the dispersion caused by the different path lengths of the various modes. Step index fiber is rare - only POF makes use of a step index design today.Graded index multimode fiber makes use of variations in the composition of the glass in the core to compensate for the different path lengths of the modes. It offers hundreds of times more bandwidth than step index fiber - up to about 2 gigahertz.Singlemode fiber shrinks the core down so small that the light can only travel in one ray. This increases the bandwidth to infinity - but it is practically limited to about 100,000 gigahertz.
Why double refraction takes place?
It happens when light enters different mediums, causing it to 'shift speeds'
What cable can transmit data at high speeds a href equals httptheypoker.com best poker bonusa a href equals httpwww.ddl.name windows recoverya a href equals httptheypoker.com poker livea a href equals?
optical fibre
Speed of a T-1 line?
The speed of a T1 line is 1.544 Mbps. It is used to transmit data over the Internet or for voice communications. Faster speeds and capacities are obtained through the the deployment of bonded T-1.
What is made up of thin glass fibers that transmit data at the fastest data speeds?
An optical fiber. Optical fibers are made of thin transparent glass or plastics that take and transmit data in the form of light, at the speed of light (whatever it is in that respective medium). Very less losses occur during data transmission, although repeaters are used after great distances to rejuvenate the signal.
Is twisted-pair cable is made up of plastic or glass fibers that transmit data at extremely fast speeds?
Twisted-pair cables are made out of copper, they are shielded with plastic to prevent electromagnetic interference but the actual cable is made out of copper.
How is a root hair cell good at its job?
Root hair cells are used in osmosis to transmit water and nutrients from the soil. These root hair cells reduce the loss of water and adapt to the large surface area and speeds up osmosis process.
