0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is valve lapping?
Is the time when intake and exhaust valve remain oper during the exhaust stroke.
How do you change four stroke engine into two stroke engine?
Nothing is impossible given enough money, determination and time to do it but ... I have to say that trying to do this idea is about as close as it comes! Two stroke relies on drawing the fuel mixture into the crankcase during the piston compression stroke to then pressurize it during the power stroke and thereby have pressure to force it up into the cylinder when the piston has traveled far enough to expose the cylinder intake port. The greatest challenge here is that the volume of a 2 stroke crankcase is specifically designed to be as small as possible with the piston at dead bottom so that all of the mixture is pushed up into the cylinder. A 4 stroke crankcase has no such constraint and is an enormous in comparison so it's volume has to be greatly reduced. *Then there's 4 stroke crankcase oil - can't be there anymore. *Then there's cylinder intake and exhaust ports to add plus how piston rings have ride past them - good luck on that modification! *Gonna need a rotary driven intake valve or a reed type check valve between the carburetor and crankcase * Throw out 4 stroke's valves, cam shaft, cam drive, push rods etc. *plug up 4 stroke valve ports in the head or make a new one with no ports. (Why did I waste my time answering this?)
What is a valve block?
Could be another name for the four stroke cylinder head, which contains the inlet / exhaust valves.
Which one is the intake valve on a 16.0 hp Briggs and stratton?
Turn the flywheel to BDC (bottom dead center) as you continue to turn the flywheel into the combustion stroke, it will be the first valve to move.
What component allows heat pump to switch between heating and cooling modes of operation?
the reversing valve is what actually changes the refrigeration cycle from heat to cool. the reversing valve receives its signal from the thermostat.
Why we open the inlet valve on the exhaust stroke and the exhaust valve on power stroke?
While there may be some overlap of valve opening timing, generally speaking, the exhaust valve opens after the power stroke, and the intake valve opens after the exhaust stroke. Recap... We start the combustion cycle of a standard 4-stroke engine with the intake stroke, the intake valve is open and the vacuum created by the downward movement of the piston draws in the air/fuel mixture from the intake manifold. The intake valve closes as the piston rounds bottom dead center and the compression stroke begins on the upward movement of the piston. At or near the top of the compression stroke, the spark plug fires (both valves are closed at this point) and begins the downward power stroke. As the piston rounds bottom dead center again, the exhaust valve opens to allow the piston to push out the exhaust gasses during the upward exhaust stroke. As the piston gets to the top, the exhaust valve closes and the intake valve opens to start the process over again.
What is the correct position of the intake valve and the exhaust valve during most of the power stage in a four-cycle engine?
Closed
What happens to a intake and exhaust valve during the power stage cycle in a four cycle gas engine?
If im not mistaken, during the power stage the intake and exhaust valves are both closed. the intake valve opens pulling air into the cylinder (cycle one) and the exhaust valve opens (cycle 4) to relase the air fuel mix that was ignited.
What is valve lapping?
Is the time when intake and exhaust valve remain oper during the exhaust stroke.
What is the correct position of the intake and exhaust valves during most of the power stage in a four cycle gas engine?
During the power or combustion stage of a piston cycle, both valves are necessarily closed, because the expansion of gases is driving the piston down.
What is valve over lap?
Is the time when intake and exhaust valve remain oper during the exhaust stroke.
Function of valve trains?
Thats Simple (: im in a techinical H.S and im learning this the main function of the valve trains is to help push close the valves in the engine during the intake stroke and the compression stroke which helps the combustion power up (: hope that helps :D
How does a four stroke engine work?
A four stroke engine has four cycles. Intake cycle, compression cycle, power cycle, and exhaust cycle. Each corresponds to one full stroke of the piston; therefore, the complete cycle requires two revolutions of the crankshaft to complete.Here is a brief explanation on how it works.Intake cycleThe intake valve opens, the piston moves downward and fuel and air is sucked into the cylinderCompression cycleThe Intake valve closes and the piston moves upward, compressing the fuel and air mixture.Power cycleA spark plug ignites the fuel/air mixture and the piston is forced downwards.Exhaust cycleThe piston moves upward and the exhaust valve opens, letting the fumes out of the cylinder.
Picture diagram of a power valve for a 1990 Yamaha yz 250?
1990 yz250 2 stroke power valve set up information, adjustment ?
Where is the glow plugs on a 2000 ford f250 power stroke?
Under the valve covers
What is the purpose of the butterfly valve inside the induction airbox of a piston engine?
The purpose of butter fly valve is to maintain one way opening during induction stroke and exhaust stroke.
Which of the following statements correctly describes the position of the intake and exhaust values during most of the power stage in a four cycle engine?
ClosedClosed.closedWhen the piston is at top dead center at the beginning of the power stroke both valves are closed, when the piston reaches dead bottom the exhaust valve opens up, when the piston reaches TDC again the intake valve opens, when the piston reaches dead bottom again both valves close to allow compression of the fuel, then at TDC the spark plug fires begins the power stroke again.They will be closed.
