0
Which one is the intake valve on a 16.0 hp Briggs and stratton?
Wiki User
∙ 14y ago
Turn the flywheel to BDC (bottom dead center) as you continue to turn the flywheel into the combustion stroke, it will be the first valve to move.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How much the thickness of sch 160?
thickness of sch160 is abt.5.5mm
What is the starter size Amps for 45KW 3Phase AC Motor connected to the pump?
160 Amp. MCCB 45 KW Contactor (67.5-112.5) Thermal Over Load
What is a pipe schedule?
Pipe schedule tell you something about the wall thickness of a pipe. Higher schedule means thicker wall. The actual thickness must be read from a pipe specification sheet, as it differs from material to material. Typical pipe sch. are Sch 20, 40, 80, 160, XS, XXS.
What is the Indian standard of SG 500 7 grade cast iron?
This is Speroidal Graphite iron casting. Mechanical Properties required are as followed, Tensile Strength ( MPa ) - Min. 500 Min. 0.2 % Proof Stress ( MPa) - Min. 320 Elongation ( % ) - Min. 7 Brinell Hardness (BHN ) - 160-240 Predominant Constituent of Matrix - Ferrite + Pearlite. Regards, Sujit Doijad 09762225010 s.doijad@rediffmail.com
Can 6000 watt electric motor power a car?
Well 1 horsepower is about 750 watts so 6000 watts is 8 horsepower. If you had 8 horsepower running to each of the four wheels ( 24,000 watts ) in direct drive with no efficiency loss do to transmission gearing and removed the engine and transmission then you be able to drive a light weight body like a geo metro. Also the type of engine you are using would be important for a car you should really look at 3 phase ac induction so you would be able to climb hills. Car hub motors are starting to enter the market they have the motor inside the rim and I have been seeing those at 8 hp at 899+. 1 company actually makes 160 hp hub motors for cars. but those cost 10k + each
What is head bolt torque for Briggs and stratton model 461707?
160 inch/pounds
What is the hp and torque for a 12 valve cummins with an aftermarket intake and exhaust?
A 1989-1993 Cummins has 160 HP stock, The 94 and 95 automatic also had 160 HP, The manual in 94 and 95 had 175 HP, a 95 High output was 180 HP. In 96-98 the auto was 175 HP and the manual was 215 HP. 1998 was the last year of the 12 Valve Cummins. An intake and a 4" exaust should add 20-30 HP and a 2-3 MPG increase on your truck.
Cost of replacing a egr valve?
The cost of replacing an EGR valve varies with the make, model and location of the car. An EGR valve for a 1996 Lincoln Town Car is about $160.
How do you clean a EGR valve on a 91 accord?
I have had to clean the EGR Valve on my 1999 Honda Accord EX V6 twice (Check engine light told me it was low EGR flow). Once at 160 k miles and I just did it again at 260,000 miles. In both cases it was NOT the EGR valve itself, but the small path from the EGR valve up to the intake manifold that was blocked solid with black carbon. the channel narrows down right at the base of the intake manifold block. To unplug it: Remove the plastic coverings on top of the intake mainfold. Then remove the ~6-8 bolts that hold down the intake manifold on top of the engine. Tilt the intakemanifold up (I left the air intake hose and throttle body attached). There was a small channel (about 1/4" wide) on the underside of the intake manifold a few inches from where the hose attaches. Use a coat hanger, small screwdriver, and/or test tube brush to dig or scrape out the built-up black carbon. (FYI-- since the EGR valve is pretty easy to remove, I'd suggest pulling it 1st to see if there is anything plugged there--- mine had soot, but was relatively clear
What is the average cost of an AFE intake system?
Expect to pay around $160 for a AFE intake system. If you look online you can find it for a little cheaper. Perhaps $120-$130.
1999 suzuki lt 160 quadrunner valve clearance?
Suzuki Quadrunner 160 Intake: 0.03-0.08 mm (0.001-0.003 in.) Exhaust: 0.05-0.10 mm (0.002-0.004 in.) At TDC of Compression Stroke. Remove the TDC plug on the crankcase, at the base of the cylinder on the left side of the engine. (left side when sitting on the atv) There will be a line on the generator rotor which will line up with a mark on the crankcase indicating TDC. I got these specs from my local suzuki dealer, so they are accurate. I will be adjusting the valves on my 160 soon.
What are torque specs for head gasket and intake manifold for 1999 Pontiac sunfire?
The 1999 Pontiac cylinder head gasket bolt torque specification is 160 pounds. The intake manifold bolt torque specification is 90 pounds.
At what point in the start up and operation procedures should you open the water outlet valve?
when the water temperature reaches 160 degrees F
What is the intake runner size on stock gm 350 heads?
It,s depending on years and type of engine but they were 160-180 cc as stock mode .
Were can you get gear solonoids for a Mercedes Benz valve chest A 160?
You could get gear solenoids for the Medcedes Benz valve chest A160 from any part store including the manufacture. Amazon also had some available for purchase.
What is 160 times 160?
160 * 160 = 25,600
What is 160 add 160?
320
