0
What would cause the power lock switch and the key to not unlock the doors of a 2001 Venture but the remote keyless entry does work?
Wiki User
∙ 17y ago
The first and cheepest thing to check is the fuses. located on the side of the dash by the passengers door, another is under the hood on top of the battery. The next would be lock switch.It is easily installed, no tools needed. The drivers side power switch is a master switch. This means that power feeds from the drivers lock switch to the passenger door. If your key fob will unlock and lock the doors but the switch will not I would replace the drivers door lock switch.
Wiki User
∙ 17y ago
Add your answer:
Earn +20 pts
How do you program a 2001 Honda Accord keyless remote?
Try this: Turn the ignition to RUN (do not start), press the unlock button on the keyless remote, ignition OFF. Repeat 2x. Turn the ignition to RUN, press the unlock button on the keyless remote twice, the power locks should cycle to indicate successful programming. Turn the ignition OFF and test remote.
How do you program a keyless entry remote for 1998 Monte Carlo?
On the inside of the keyless entry remote or sometimes on the back it explains how to do this. I believe you hold the unlock button along with the lock button for 7 seconds near the car. It will explain it on the inside of the keyless entry remote.
How do you program a avx01bt3cl3 keyless entry remote?
Turn ignition switch to 'On'. Press valet button 3 times, you will hear one beep, press 'lock' on remote. Press valet button 4 times, you will hear two beeps, press 'unlock' on remote. Should be programmed now to lock/unlock car.
How do you program new remote keyless entry for 2005 Chevrolet Uplander?
# Close all the vehicle doors. # Insert the ignition key into the ignition lock cylinder. # Press and hold the DOOR unlock switch. # While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF. # Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode. # Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter. # Repeat the previous step to program up to four transmitters. # Turn the ignition switch to the RUN (one more click forward) position in order to exit the keyless entry transmitter mode. # Operate the transmitter functions in order to verify correct system operation.
How do you unlock a 2001 Chevy Suburban?
Put the appropriate key in the door, and turn. Or use the remote if you have keyless entry.
How do you reset the security system in your 2000 Chrysler Sebring without a keyless remote?
Unlock the doors or trunk with the key.
How do you program a 2001 Saturn L200 keyless entry remote?
You can program the keyless entry remote, for your 2001 Saturn L200, by holding the unlock and lock weapons at the same time. The red light will flash on and off. The remote will be programmed when the red light stays illuminated.
How do you disarm 1998 jeep without keyless remote?
First unlock and open the hatch, the horn alarm is now disarmed and you can unlock the driver side door.
Program remote keyless entry on 1996 Chevrolet pickup?
To program a remote keyless entry on 1996 Chevrolet pickup, first hold down the power unlock button of the door panel. Second, turn ignition key ON, OFF, ON, OFF. Then release power unlock button on the door panel.
How do you program keyless remote for 2003 GMC sierra?
Close all the vehicle doors.Insert the ignition key into the ignition lock cylinder - do not turn ignition switch.Press and hold the DOOR unlock switch (This is the switch on the door, NOT the remote).While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF ON, OFF. (3 TIMES)Release the DOOR unlock switch. The doors will lock and unlock one time to confirm the program mode is actuated. Remove the key from the ignition.Simultaneously press and hold the LOCK button and the UNLOCK button on one key less remote for approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.Repeat the previous step to program up to four transmitters. Reprogram any existing remotes at this time as they have been erased.Turn the ignition switch to the ON (one more click forward) position in order to exit the keyless entry transmitter mode.Operate the transmitter functions in order to verify correct system operation.
How do you Program kobut1bt?
KOBUT1BT is the FCC ID# on the back of keyless entry remotes for 2000-2001 Chevy Full Size Pickup/1998-2004 Chevy S-10 Pickup/2000-2001 Chevy Suburban & Tahoe. And it's easy to program these remotes without having to pay dealership "ripoff" prices. 01: Close all vehicle doors02: Insert key into ignition03: Press and hold driver's door unlock switch04: Cycle igniton On_Off_On_Off05: Release unlock switch Doors will lock and unlock to confirm programming mode 06: Press and hold lock & unlock buttons on keyless remote Doors will lock and unlock to confrim keyless remote programmed 07: Release lock & unlock buttons on keyless remote Repeat steps 06 & 07 on all remotes you have for vehicle because programming first remote erases programming on additional remotes. 08: Turn igniton on to exit programming mode Up to four remotes can be programmed to one vehicle.
How do you program keyless for a Cadillac dts?
Change batteries and press lock and unlock remote at the same time for (8) second.
