0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What should you do if your circuit breaker is hot?
You should check that you are not running too many appliances on the circuit that is protected by the circuit breaker.If you are absolutely sure that the circuit is not being overloaded, you should replace the breaker with a new identical breaker. Breakers get hot when they supply power at near peak amperage over a long period of time and begin to break down internally.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
Can a 15 amp breaker be replaced with a 20 amp?
Please be more specific....simply replacing the breaker with a 20 amp may cause a fire; if the cable is sized for 15 amp and is overloaded. Your 15 amp breaker is probably feeding #14 wire. The use of a 20 amp breaker requires at least a #12 wire be used. Fire hazard if breakers and wiring are not sized correctly.
What is a circular path that electricity flows in?
A circular path that electricity flow in is called a "circuit". A circuit does not have to be circular in shape, but must begin and end at the same point like a circle does.
Why the fuse wire reduces the danger of fire in a building?
A short in an electrical circuit could cause the cables to become red hot, causing an electrical fire. Before the cables begin to heat up, the thinner fuse wire will blow, or a breaker will trip, and the circuit will become open before any damage occurs.
How do you fix an automotive short circuit?
Depends on what you did and what the car is or is not doing. Not doing anything, you either burned out one or more of the heavy fuses under the hood or burned through what is called a fuse-able link. That is a heavy section of wire either by the battery or the fuse box under the hood. They burn through if the short continues after the fuse blows or if it is on a circuit that is not fused. None of this is tragic or hard to fix, it just takes a little time. There are probably 3 or 4 of the fuse-able links in a group. Different colored wires about 6 inches long that probably have a tag in the middle that says fuse-able link. Most fuse blocks under the hood are on the drivers side inner fender.
What to do when computer circuit breaker reset button begin to make noises?
Have the circuit breaker replaced.
Is there any disadvantage of selecting over rated circuit breaker?
If i understand you correctly, yes there certainly can be. If you replace, say a 10 amp breaker with a 20 amp. you are losing the safety factor - the whole purpose of the breaker to begin with. Always replace a breaker with the exact same amperage rating!
What is different Circuit Breker And Isolater?
I think that the questioner is asking what is the difference between an isolator and a circuit breaker.A circuit breaker is a switching device designed to interrupt a fault current.An isolator is not intended to break a live circuit but, rather, to provide a visible separation between a circuit component and live conductors.For example, isolators (or 'disconnectors' in US parlance) are located on either side of a high-voltage circuit breaker. If the circuit breaker requires maintenance, then the procedure is to:a. trip the circuit breaker.b. open the isolators on each side of the circuit breaker, so there is a visible gap between the circuit breaker and the 'hot' conductors.c. apply temporary earths (grounds) between each isolator and the circuit breaker.d. complete a 'permit to work' card.e. begin work.
What should you do if your circuit breaker is hot?
You should check that you are not running too many appliances on the circuit that is protected by the circuit breaker.If you are absolutely sure that the circuit is not being overloaded, you should replace the breaker with a new identical breaker. Breakers get hot when they supply power at near peak amperage over a long period of time and begin to break down internally.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
What should you do if someone have an electric shock?
Without touching the victim, remove them from the circuit. In the home, where the voltage is usually 240 volts or less, you can push them off with a wooden broom handle or pull them off with a rope. The moisture in those objects can turn them into conductors at higher voltages such as you might encounter in an industrial setting. The safest way to remove the victim from the circuit is to turn the power off at the circuit breaker panel or light switch. Go now and identify where your main breaker is. Don't forget that if you turn off the power at the main, your cordless phones probably won't work. Once the victim is out of the circuit, call emergency services and begin CPR.
What are some adjectives that describe a house and begin with the letter O?
Some houses are old. Some houses look odd. Some houses are outlandish.
What houses and shelters begin with the letter q?
Quonset Hut
What did wealthy merchants begin spending their money on?
Houses and Luxuries.
In a circuit where does the current begin?
The current flows from negative to positive.
Where does every circuit begin and end?
each circuit begins and ends at the heart, and blood travels through these circuits in sequence (:
When did the white houses construction begin?
The construction began April 1834.
How would a chiropractor's explanation begin?
Began cause people needed houses.
