Thermostats
Acura Integra

When upper radiator hose on 1993 acura integra is removed there is no thermostat any ideas?

123

Top Answer
User Avatar
Wiki User
Answered
2010-06-19 20:12:04
2010-06-19 20:12:04

theromstat housing on the back not the front

001
๐Ÿ˜‚
0
๐ŸŽƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Related Questions


The thermostat is located at the other end of upper radiator hose.


Follow the lower radiator hose from the radiator to the engine, that's where it is.


The thermostat is inside its housing on the upper radiator hose on the engine block side.


On the other end of the large top-left radiator hose.


Should be a in a removable housing at the engine end of the upper radiator hose


just follow the lower radiator hose to the engine and that is where it is sitting@


If yoor 1996 Integra has the1.8L engine, the thermostat is located at the back of the motor at the end of the bottom radiator hose.



follow your lower radiator hose to where it connects to the engine block remove that hose and there u go thermostat will be inside the thermostat housing right underneath


check to be sure that the thermostat is not backwards and is the correct heat rated unit for the car


http://wiki.answers.com/Q/Where_is_the_thermostat_on_1987_acura_integra


The radiator support on a 1991 Acura Integra is held on with several bolts. Use the appropriate sized socket and loosen all the bolts. Pull off the support.



91 acura integra has a b18 91 acura integra has a b18


The way to replace the thermostat on a 91 Acura Legend Coupe is to drain the radiator and remove the throttle and cable box. Remove the top of the radiator hose and the bolts. The thermostat will be inside.


The thermostat on a 95 acura integra ls is located on the left back side of the engine. below the intake. You will see a sensor plug-ed into it. The thermostat has 2 ten mill bolts holding it together and they are a pain. The best tool for the job is a ratchet wrench.


The water pump on a 94 Acura Integra is located on the front of the engine. It uses the power of the engine to circulate hot water from the engine to the radiator to cool it.


if u do it urself n buy the radiator for liek 120-150 bucks


The drain plug is on the drivers side of the radiator. It is almost straight down from the headlight assembly.


trace the lower radiator hose to the engine, that's where the thermostat located.


follow the bottom hose on the radiator to where it connects to the engine. Inside that connector is the where the thermostat goes. make sure you use some RTV gasket sealer for reassembly.



unlike most conventional vehicles where the thermostat housing is located on the block at the end of the upper radiator hose. the thermostat housing in a 95' acura integra ls is located on the block behind the distributor at the end of the lower radiator hose. first you want to disconnect the negative battery connection, setting if to the side making sure its not able to reconnect with the battery. drain your cooling sytem by removing the radiator cap and plug(found on bottom passenger side of radiator). then undue all electrical connections to the thermostat. unbolt the two connecting bolts holding the thermostat housing in place, remove the lower radiator connecting hose from the thermostat housing, off setting it upwards to deter any residual coolant from leaking on the engine block. completely remove the bolts holding the housing in place. remove the housing, exposing the thermostat. remove the old thermostat and compare it to the new thermostat( checking diameter and condition). clean the housing and thermostat port of any debris. fit the new thermostat with a new gasket and place in the thermostat port in the block the same way you removed the old one. reinstall the housing, bolting it in place. reinstall the lower radiator connecting hose to the thermostat housing on the block. refit your electrical connections to the thermostat, reattach the negative connection to the battery and refill your cooling system.


Remove the top radiator hose from the thermostat housing, its the round thing up front of the motor that the hose leads to it from the radiator. Then remove the bolts holding on to the top part of the housing, replace and reset all parts removed.


How to install a boost gauge in a acura integra?"



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.