Transmissions and Drivetrains
Nissan Maxima

Where are the water hoses conected to transmissionfor Nissan Maxima 1996?

212223

Top Answer
User Avatar
Wiki User
2006-04-18 01:23:35
2006-04-18 01:23:35

autozone.com on the right click repair and follow the directions, then click on drivetrain and look it up.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

I need to find where are my vacuume hoses on a 1992 Nissan maxima se...

User Avatar

check your vacuum hoses, they could be loose or they could have a leak

User Avatar

the thicker hoses are oil cooler hoses the thin ones are cooling line for auto transmission

User Avatar

You need to replace the purge valve and clean all of the hoses. I hope that help

User Avatar

its on the left side of the engine block passenger side. it has 4 screws. its hard to get to . a tight spot . located under the larger radiator hoses.1994 max.

User Avatar

I dont know about your specific car but its usually located on one of the hoses coming from the heater core, on the firewall, behind the engine.

User Avatar

THis is radiator Fluid. Also known as coolant. Either you have a radiotor leak, your water pump is leaking, or one of you coolant hoses is broken (more than likely its a hose)

User Avatar

It's under the left 1/4 panel below and behind the fuel door area. It's a square plastic part with a few hoses connected to it.

User Avatar

As long as you are taking it all apart, you should replace the radiator hoses, heater hoses, and accessory drive belt(s.) Be sure to get the gasket for the pump, and some hi-temp (red or blue) silicone to seal it up.

User Avatar

it is right under the master brake cylinder wher u put brake oil it is undernaeth there its a metal or aluminum filter ez to do yourself unplug the gas hoses and reconnect with new one

User Avatar

To insure that the power steering hose can route properly, the hose needs to be an exact replacement. The hoses are under pressure, tighten the connections snug but not too tight to prevent leakage.

User Avatar

P1447 CODE IN MAXIMA , SANTRA, AND ALL NISSAN CARS MEANS // - GAS FUMES FROM GAS TANK TO EVAP VALUE // LEAKING IN SHORT GAS IS LEAKING(FUMES) ... .. SO CHECK FOR CRACK RUBBER HOSES AND REPLACE THEM... CODE WILL GO AWAY....

User Avatar

It is bolted to the engine block. There are 2 large hoses connected to the radiator. One is on the top of the radiator and the other is at the bottom. The bottom hose connects to the thermostat housing which contains the thermostat inside of it as one piece.

User Avatar

go to the back seat and pull the two tabs in between the seat and the floor and pull the seat up and out. And you will see the fuel pump, remove all hoses and bolts and it comes out, dont be surprised if you spill a little fuel.

User Avatar

I person needs to have a diagram when making any changes to a car. For a Nissan Sunny B12 the diagram to the air hoses connected to the intake manifold and carburetor can be found in the maintenance manual.

User Avatar

The abs works electrically. There should be sensors at each wheel, and a fuse just for the abs system. Check the fuse first.

User Avatar

just did this one... i took off the intake manifold and all wires and vaccum hoses conected and then just moved it to the side. gives you plenty of room to remove/install the starter.

User Avatar

it has two thermostats follow the water hoses one on right side the other is in the front

User Avatar

You don't even need to move any hoses. There are 4 screws on the airbox. Just unscrew them and replace the filter. Hope that heps! =)

User Avatar

It's in the intake one of the bigger hoses that go in. You have to use a wrench to remove it.

User Avatar

It's on the fire wall on the driver side. Release the pressure and pull the hoses off. Put the hoses on the new filter making sure the flow is the right way and your all done.

User Avatar

They either carry coolant, lubricant, or vacuum. There are also hoses for the A/C.

User Avatar

the starter is located right benaeth the intake manifold you must take out the air filter housing and disconnect all the lil hoses which are going into the air box and it will be visible right underneath but you will need alot of leevrae to undo the bolts it is ver hard to do i have done it takes 30-45 mins sometimes even an hoir good luck

User Avatar

# Idle speed incorrect # Fuel filter clogged and/or water and impurities in the fuel system # Faulty emissions system components # Faulty or incorrectly gapped spark plugs # Faulty spark plug wires # Vacuum leak in the fuel injection system,intake manifold or vacuum hoses # Valve clearances incorrectly set


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.