0
It's near the base of the strut on the inside
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
How do you change a Renault clio front strutt?
First, open the hood. Now remove the brake line support so that you can begin to get to the strut. Remove the pinch bolt that holds the strut at the bottom. Drop the sway bar that is connected to the strut. Now remove the bolts the interior bolts that support the strut. Remove the old strut and replace it with the new one.
How do you change a rear strut on a Mercury Topaz?
1986-1994 models # Loosen but dont remove the upper mount-to-shock tower nuts # Raise and support car # Remove the wheel and tire assembly # Remove the brake flex line-to-strut bolt # Remove the strut-to-knuckle pinch bolts # Using a suitable tool spread knuckle-to-strut pinch joint slightly # Using a suitable prybar place top of bar under fender apron and pry down on knuckle unil strut separates from knuckle be careful not to pinch the brake hose
How do you remove the front struts?
RemovalDisconnect the battery negative cable.Loosen the four strut mounting bolts in the engine compartment several turns. Do not remove yet.Place the vehicle on jack stands.Remove the front wheels.Remove the brake line from the clip on the front strut.At the bottom of the strut, there are two bolts which attach the front strut to the spindle assembly. The top bolt is an eccentric bolt which provides for adjustment of the wheel camber. Using a paint pen, scribe, or brightly colored nail polish, mark the orientation of the eccentric bolt to the strut.Remove the eccentric bolt and bottom retaining bolt from the bottom of the strut.Pull the strut away from the spindle until it is free from the bottom of the assembly.Hold the strut while removing the four mounting bolts at the top of the strut. Remove strut from the vehicle.If the strut is to be replaced, note the orientation of the eccentric bolt alignment mark from Step six and transfer that mark to the new strut
Replace struts on 2003 town and country?
You will need to compress the strut spring with a spring compressor. When the strut spring is compressed remove the strut retaining bolts. There is a strut retaining bolt on the top and the bottom of the strut assembly. Reverse the process to install the new strut.
How to replace control arm - ball joint 1986-1995 Taurus Sable?
According to the Chiltons Repair Manual, on 1986-1995 Taurus / Sables, the lower ball joint is an integral part of the lower control arm and is not replaceable - replace the lower control arm as an assembly.Replacing the lower control arm isn't all that bad of a project...Prep: Raise and support front end - remove wheel, caliper, rotor* Remove 'tension strut' nut - that's the bar coming from the frame out to the middle of the lower control arm * Remove the 'pinch bolt' at the bottom of the steering knuckle holding the lower control arm / ball joint stem - it would help to open up the pinch with a small pry bar * Remove bolts from inside control arm frame mounting / pivot point Install:* Place control arm over the end of the tension strut* Reattach control arm to frame pivot point - torque nut to 73-97 ft. lbs. * Align the 'grove' in the ball joint stud with the pinch bolt opening -* Line the stud up with the angle of the steering knuckle opening and insert * Insert pinch bolt and torque to 40-53 ft. lbs. * Time to put the nut and dished washer on the tension strut - dished washer facing AWAY from control arm (frontwards) - torque to 73-97 ft. lbs. Re-install caliper, rotor and don't forget the front wheel.
How do you replace struts on 1993 mercury villager?
Compress the shock spring with a spring compressor. Remove the top strut bolt. Remove the bottom strut bolt. Reverse the process to install the new struts.
How do you remove and replace a front strut on 97 Nissan Sentra GXE?
Remove the bolt on the botton of the Strut. Detach the steering Knuckle. Remove the three nuts on top and remove the strut from the car. Do not try and disamble the strut without a spring compresor. Get a whole new strut. Good luck
What is a steering shaft pinch bolt?
this is the bolt that pinches together one of the joints on the shaft this will be a joint that slides into another
What is the head bolt and intake torque specs 1997 Ford Taurus gl?
torque for 97 taurus head
How do you change a strut bearing on your mk1 Renault clio?
remove the 22mm bolt at the top that holds the strut to the car DO NOT REMOVE THE 19MM NUT ON THE STRUT ITSELF UNLESS YOU HAVE USED A SPRING COMPRESSOR TO RELIEVE TENSION OF THE SPRING
Will OEM rims from a 2000 Taurus fit on a 1997 Ford Taurus?
The bolt pattern on the 1996 Taurus to 2004 Taurus is the same , its 5 on 4 and 3/4, so it will fit.
How do remove and replace a strut on a 97 Nissan Sentra GXE?
Honda calls it a damper. If you want the front damper. Remove the brake hose clamps from the damper remove the damper pinch bolt (on the bottom). Remove the damper fork bolt. then remove the damper by removing the two 10 mm nuts on top. Do not try to Disassemble the Damper without a spring compressor.
