answersLogoWhite

0


Best Answer

The slave cylinder for a hydraulic clutch is inside the manual transmission bell housing

User Avatar

Wiki User

โˆ™ 2009-02-12 15:49:43
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: Where is a slave cylinder on a 95 ford ranger?
Write your answer...
Submit
Related questions

Does a 95' ranger have a cable or hydraulic clutch?

Hydraulic and the slave cylinder is in the bell housing.


How much horsepower on a 4 cylinder 95 ford ranger?

( 100 horsepower ) according to ( the ranger station . com ) no spaces


95 Ford Ranger 4-cylinder 8 spark plug compression test?

pounds of compression per cylinder


How do you remove hydraulic clutch line 95 ford ranger manuel?

on the side of the trans where the slave cylinder goes into the bell housing, there is a gold fitting attaching the hyd. line to the slave. on that gold fitting there is a white plastic band that needs to be pushed down towards the slave cylinder. push it in far enough and the line will pull free.


How do you change dash lights on a 95 Ford Ranger?

How to change dash lights on a 95 Ford Ranger?


How many spark plugsin a 1994 Ford Ranger 4 cylinder?

4 - modern combustion engines use 1 spark plug per cylinder. ANSWER The 1994 Ford Ranger 2.3 L has Ford's twin plug ignition system , so there are 8 spark plugs The 94-95 Ranger 2.3 has twin plug system, 2 per cylinder =8


Does a 95 Ford Ranger with a 4 cylinder engine have a non-interference fit engine?

Yes , according to the Gates and Dayco websites ( They make timing belts ) the 2.3 liter four cylinder used in the 1995 Ford Ranger is NOT AN INTERFERENCE engine


Where is the camshaft position sensor on a 95 ford ranger 4-cylinder?

There isn't one. It only has a dual vane crankshaft position sensor.


Where is 95 Ford Ranger relay block?

The relay block on the 95 Ford Ranger is under the hood. It is on the driver's side on the front side of the wheelwell.


How do you find the 1 cylinder on 95 ford ranger?

On the 2. 3 L four cylinder , the # 1 cylinder is at the front of the engine and on the 3.0 L and 4.0 L V6 engines , the # 1 cylinder is at the front of the engine on the passenger side


On my 95 ranger the clutch will disengage but will not reengage for 5-10 seconds after i release pedal could this be a slave cylinder problem?

Sounds like your clutch disc is worn out and slipping.


How do you replace the rad hoses on a 1996 Ford Ranger?

How do I remove air from the cooling system of a 95 ford ranger 4 cyl


What is compatible with a 94 ranger XLT transmission?

is a 95 automatic 4cyl ford ranger transmission compatible with a 94 ranger 4cyl?


Where is the transmission on a 95 Ford Ranger?

The transmission is bolted to the back of the engine


Will ford explorer seats fit a 1999 ranger ext cab and what years?

will 95 explorer seats fill my 99 ford ranger ext cab


What type of brake fluid for a 95 Ford Ranger?

For a 1995 Ford Ranger ( in North America ) ( DOT 3 brake fluid meeting Ford specification ESA-M6C25-A )


Will a 91 Ford Ranger automatic transmission fit in a 95 Ford Ranger?

Yes if they both have the same engine size and both are either 2wd or both are 4wd.


What type of oil for a 95 Ford Ranger?

For a 1995 Ford Ranger : ( 5W-30 is the PREFERRED oil ) * 2.3 / 3.0 / 4.0


Having brake problems on a 95 ford ranger xlt 2.3l v6 you replaced master cylinder brake booster bled the brakes pedal still goes to the floor?

You need to bleed the brakes.


Where is the slave cylinder on a 95 Chevy Cheyenne 4x4 1500?

It is straight underneath the starter


How do you remove the front clip on a 95 ford ranger?

It takes a cutting torch.


Is there a cabin filter in a 95 ford ranger xlt?

No , there isn't a cabin filter


Where is the clutch bleeder on a 95 jeep wrangler the master cylinder broke you replaced it and cant find the bleeder screw it is not on the slave cylinder?

== == == ==


Where is the block heather on a 95 ford ranger?

The block heater on a 1995 Ford Ranger is in the engine space under the hood. The plug for the heater block is located near the front of the engine.


Why will my 95 Ford Ranger low beams work but not the high beams?

If it's the same as the 1996 Ford Ranger , fuse # 33 is a 15 amp fuse for the High beam lamps