0
It is located an axle that connect your wheel to the transmission. If you look under the car, it is the part that has two rubber "boots" on both ends. one end is by the wheel, the other, in the transmission
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How to change cv joint on 97 Honda Accord lx?
1997 Honda accord special addition
How do you replace the passenger side CV shaft on a 1996 Honda Accord?
Listen to your father: go to the nearest public library and get a Honda manual--it will describe everything in detail!
How do you remove a front axle on a Honda 420 rancher 4x4?
How do you get the axle out to change the boots on the cv joints
How do you replace a cv joint in a Honda Odyssey?
Much better to replace the whole axle, look at www.happywrenching.com for a guide on how to replace an axle in a Honda Odyssey
What is the size of a 1998 Honda accord cv joint nut?
32 mm
Where can you buy a CV Joint for a Honda Civic 1998?
http://www.autozone.com/autozone/parts/1998-Honda-Civic-EX/CV-Axle/_/N-jaf2pZ6o2dc?sortType=low
What makes the front right tire on 1986 Honda accord pop and creak when you turn or go over bumps?
The CV joint has gone bad. You can purchase a rebuilt drive axle and CV joint on eBay for $49.00. I would recommend changing them both at the same time.
Does a 5-speed 1998 Honda Accord have universal joints?
It has CV joints which are similar to Universal Joints.
How long does it take to change cv joints on a 93 Honda accord?
30 mins to 1 hour
How to you change CV joints on a 1996 Honda Accord?
It is more cost effective to replace the CV axle which has the new joints installed. Check with pep boys, autozone, etc., ask to price a remanufactured CV axle. = _______________________________________ = = How to Replace CV Axles on a Honda Accord = The 1990-1996 Honda Accord uses CV axles as the drive shafts, as do all front-wheel drive vehicles. It is used to transfer the power from the transaxle to the front wheels. When CV axles wear out, they will emit a clicking noise when the car is turned to the right or left. The most common cause of CV failure is a broken CV boot. The boot covers the swivel joint and contains the grease for lubrication of the joint. When the boot breaks, the grease is lost and the joint begins to wear out. Instructions Step 1 Jack the vehicle up and support it on jack stands. Remove the both front wheels. Using the 36 mm socket, remove the center axle nut. Remove the though-bolt on the bottom of the strut where it attaches to the spindle. Step 2 Separate the bottom ball joint from the spindle using the ball joint separator. Using the pry bar, pry the lower control arm down to pull the separated ball joint out of the spindle and push the spindle out of the way toward the rear of the car. Step 3 Use the pry bar to pry the CV axle out of the transaxle. Put the pry bar between the transaxle case and the CV axle, and push it out. Remove the CV axle and put it in the box the new axle came in---CV axles carry a core fee, which is refundable upon return of the old axle. Step 4 Install the new CV axle by inserting it into the transaxle up to the snap ring clip where it will stop. With both hands, pull it back about an inch and slam it in with a fast push, and you will feel it snap into the locked position. Step 5 Grab the brake rotor, pull it outward and insert the outer end of the CV axle into the hub in the rotor. Rotate the rotor back and forth to line up the splines and push the axle in as far as possible. Loosely screw on the axle nut. Step 6 Pull the lower control arm down with the pry bar. Line the ball joint up with the hole in the spindle and insert the ball joint. Install the nut on top of the ball joint and tighten it down. Step 7 Install the bolt in the bottom of the strut where it attaches to the spindle and tighten. Torque the axle nut to 180 foot pounds. Put the wheel on and repeat from Step 1 for the other side.
How do you Replace the left cv joint on a 1989 Honda Accord?
The left CV joint can be replaced on a 1989 Honda Accord by removing the left tire and the moving the brake lines. Next, the ball joint and the tie rod should be removed, which will allow for their to be enough room to use a pry bar against the transmission which will pop out the CV joint.
How do you get the cv axle to stay in the transmission on my 92 accord?
I belive there is a snap ring one the end of the axle that keeps it in. On the end that goes into the transmission, about a quarter of an inch from the end there should be a groove in the axle. If there is, there should be a ring in it.
