Best Answer

the intake air temp sensor is in the inlet manifold

User Avatar

Wiki User

โˆ™ 2006-10-14 05:28:18
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Where is the IAT sensor in a 97 EL Ford Falcon?
Write your answer...
Related questions

Were is the iat sensor on a 97 blazer?

iat sensor on a 97 blazer and what does it do

Locating IAT sensor on 97 ram 2500?

The IAT sensor for a 97 Ram 2500 is on top of the engine. It is at the front on the passenger side of the intake.

Where is the iat sensor located on a 97 powerstroke?

The IAT sensor can be found on the top of the engine. The sensor will be near the fuel injector rail. The sensor should be labeled as such.

Where is the IAT sensor on a 97 maxima located exactly?

its in the back wheel under the rotator splint

What if the iat sensor malfunctions on a 97 blazer?

The "Check engine" light will illuminate and a code will set.

Where is the Location of IAT sensor in 97 sonata?

The intake air temperature (IAT) sensor of the 1997 Hyundai Sonata is located in the air hose assembly. Follow the air hose to the immediate entrance to the air filter box and that is where to find the IAT wiring harness.

Where is the IAT sensor location on a 1997 Mazda miata?

The IAT on a 94-97 models is not a separate component, like on later models. It is included in the Mass Air Flow Sensor. The Mass Air Flow Sensor is the black, plastic tubular component connected at the top of your airbox on the driver's side.

Where is the IAT sensor on a 97' Jeep Grand Cherokee with a v8?

On the front passenger side corner of the intake. It has two wires.

What is the sensor on a 97 Ford Ranger master cylinder resivior caller?

I believe Ford calls it the " brake fluid level sensor "

Is the air temp sensor on the back of the inlet manifold on a 97 xh Ford Falcon ute?

assuming it's the 4 litre. yes it is. hard to change on the ground. easy to get from under the car.

Where is the IAT located on 97 LHS?

It should be in the air boot between the air filter box and throttle body (it is a two wire sensor)

Changed fuel filter '97 4cyl pu truck ce light came on code reader said iat sensor circuit malfunction replaced the iat sensor and had the codes cleared and the check engine light came back on?

Be sure to check the wires going to the IAT sensor. Nissan used cheap wiring for this and it usually breaks. The problem is the wires constantly flex when the engine moves.

What are the resistance specs on the iat sensor on a 97 aspire?

Never mind, got it from all-data, BTW the haynes book is totaly wrong, what a surprise.

Which was the maximum speed of Ford Falcon wagon 6cyl 132HP 1975?

153 kph (97 mph)

Where is the speed sensor located on a 97 ford wind star?

The speed sensor on a 97 Ford Windstar van is located on the side of the transmission. It tells the vehicle's engine vital information which it uses to make constant adjustments.

Where is the intake air temp sensor IAT on a 97 Grand Cherokee 6-cylinder?


Where is bank 1 sensor 2 on a 97 Ford Explorer?

Bank 1 is the passenger side of the engine in a Ford Explorer Sensor 2 is in the exhaust AFTER the catalytic converter ( downstream )

How do you fix a 97 Ford Escort with an O2 sensor circuit that has low voltage?

Sounds like you need a new 02 sensor.

97 Ford explorer VSS sensor not working?

Replace it.......its one bolt on the side of the transmission.....

Where is the TPS on a 97 Ford Expedition?

The Throttle position sensor is monted on the side of the throttle body .

How do you install knock sensor in a 97 ford expedition?

On the 5.4 the knock sensor is under the intake and the connector is in the back of the motor on the passenger side.

Location camshaft sensor on 97 ford f-150xl 6cyl?

under the water pump.

Location of a 97 ford explorer temp sensor?

Directly behind the top radiator hose to the engine.

Where on the transmission is the speed sensor for a 2000 Ford Ranger?

only 97 and earlier models have speed sensors

Mass Air flow sensor 97 ford explorer 5.0?

The mass air flow sensor commonly becomes dirty. The sensor can be removed, and the sensor wires can be cleaned to work like new.