0
The PCV valve on the 98 is located in the top of the right (driver's side) valve cover near the back.
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
Do all 1994 Ford Ranger 40 have an EGR Valve?
yes 2002 and later 30L are the only ones not equipped with an egr valve
Where is the PVC valve on a 2001 Toyota 4 runner?
do you want that PVC in schedule 40 or schedule 80,1",2"? its a PCV-(Positive Crankcase ventilation )valve.
How much does a brake calliper cost for a 1986 Ford Ranger?
A brake calliper for a 1986 Ford Ranger would be likely to cost between $20 and $40, depending on where you source it.
Where is the E G R valve located on a 1994 ranger 40?
its at the right rear corner of the intake manifold
Is it ok to use 10W-40 oil in a 2000 Ford Ranger truck?
Yes it is fine to use 10W-40 oil
Your 88 ford ranger has 40 psi to the scharder valve while running good when running bad has 30psi what is wrong?
There may be issues with the fuel pump or the fuel filter may be in need of replacement among other things.
What is the oil pressure on 2001 Ford Ranger with 3.0 engine?
I'm not a mechanic / technician but I BELIEVE that is ( 40 to 60 PSI at 2,000 RPM ) for the oil pressure on a 3.0 liter V6 engine in a Ford Ranger
Oil pan gasket 2002 Ford Ranger replacement?
A replacement part for a 2002 Ford Ranger oil pan gasket will cost a price close to $40. The part can be purchased from a auto parts store.
What are the torque specs for the water pump on a 1999 ford ranger 3.0?
The 1999 Ford Ranger 3.0 liter water pump bolt torque specifications are 40 pounds. You do not want to torque the bolts to hard or they will break.
How do you change a PCV Valve on a 2005 Jeep LIberty?
On the 3.7 Liter V6 engine the PCV valve is located on the passenger side of the oil filler neck. The valve itself is a small black plastic device with a right angle bend in it. One end inserts into the oil filler neck and the other end has a hose attached to it. 1. Remove the hose from the PCV valve. 2. Turn the PCV valve counter-clockwise, approximately 90 degrees, until the retaining pin (can't see it when the valve is installed but its on the side of PCV valve, you should be able to get the idea if you look at the replacement PCV valve) is aligned with the slot on the oil filler neck. Once the pin and slot are aligned you will be able to wiggle the PCV valve out of the oil filler neck. The PCV valve has an o-ring that gives some slight resistance to removal. 3. Clean out the PCV valve mounting hole with some paper toweling or rag. Lubricate the new PCV valve o-ring with silicone spray, wd-40, petroleum jell or similar. This will help with insertion. 4. Install new PCV value in opposite order of removal. ---------------- Just wanted to add on to this in case your PCV valve in the '05 is the same as the '06+. In those years, on a 3.7L V6, there are 2 PCV valves. They are located at the rear of each bank of injectors/spark plug coils near the fire wall. Attached to those valves is a black rubber hose approx. 6 inches long and curbed into a 90 degree turn. Those both then attach to black plastic tubing that joins at the front left of the engine at a T-fitting that goes into the airbox. To change the PCV valves in that scenario, you will need to pull off the black hose at each valve and undo screw each valve using a hex fitting. One that is attached to a socket is probably best. I do not know the size but it is larger than 1/2". They should unscrew like any other bolt and replaced. After replacing the valves, slide the black hose back onto the valves.
What are the valve cover torque specs for a 93 ford explorer 40 v6?
53-70 in-lbs
Where is the ignition module located on a 1994 ford ranger with a 40 liter?
its mounted under the hood on the driver side fender
