0
its at the front of the engine directly under the ignition coil pack.remove the four screws holding the coil to its bracket,flip the coil over on its back and youll see the cam sensor below.its held in place with 2 tiny bolts-5mm head I think
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
95 crown vic Where is the camshaft position sensor?
The 1995 for Crown Victoria camshaft position sensor can be found on the back of the cylinder head. The camshaft position sensor will be labeled as such.
Where is the camshaft position sensor located on a 1995 Mitsubishi Galant?
Inside the distributor
Where is the camshaft position sensor located on a 1995 Chevy Tahoe?
That year did not have 1
Where is camshaft position sensor located on 1995 chev truck?
There is no cam sensor on the 1995 year engine. GM. did not use a cam sensor on that year.
Where is the camshaft position sensor on a 1995 ford ranger 4.0 L OHV?
I have the same engine in my 1995 Ford EXPLORER : I can't see the camshaft position sensor but from what I have read it is on the top of the engine , near the center line , at the back of the engine near the firewall
Where is the camshaft position sensor on a 95 dodge ram 5.2?
The camshaft position sensor, which is located inside the distributor, is a pretty easy component to test on the 1992-1995 5.2L/5.9L Dodge Ram 1500/2500 pickup.
Where is the camshaft position sensor switch located on your 1995 Durango?
The Dodge Durango was introduced in 1998, so this question cannot be answered. However, in the 2000 Durango.... The camshaft position sensor is located in the distributor on all 3.9L V-6 and 5.2/5.9L V-8 engines Camshaft Position Sensor REMOVAL Distributor removal is not necessary to remove camshaft position sensor Remove air cleaner assembly. Disconnect negative cable from battery. Remove distributor cap from distributor (two screws) Disconnect camshaft position sensor wiring harness from main engine wiring harness. Remove distributor rotor from distributor shaft. Lift the camshaft position sensor assembly from the distributor housing Camshaft Position Sensor INSTALLATION Install camshaft position sensor to distributor. Align sensor into notch on distributor housing. Connect wiring harness. Install rotor. Install distributor cap. Tighten mounting screws. Install air cleaner assembly. (this info from post on answers.com about cps on 2000 durango)
Where is camshaft sensor on 1995 Nissan altima?
The Camshaft sensor is located under the cap and rotor of the distributor. This is a common failure on the 2.4L engine due to oil leakage into the distributor. how is the camshaft sensor replaced on 1995 Nissan altima. what other considerations are there.
You had change the crankshaft position sensor on your 1995 Lincoln Continental and still wont start any ideas?
try to replace the camshaft position sensor located under the power steering resivoir .. on 4.6 liter lincoln ...
Where is the cid sensor on a 94 ford escort 1.9?
There isn't one on the 1.9l. Only on hte 1.8l and then it's within the distributer. BUT on the California model, and cars sold with the early 1995 engine, there is a crankshaft position sensor, and a camshaft position sensor. The camshaft position sensor is the likely culprit of a CID sensor code and it's installed in the back side of the cylinder head between the head and the intake manifold where the throttle body bolts on.
1995 Ford Mustang MAP sensor Location?
I don't think a Mustang has a MAP sensor. They are MAF system.
Where is the camshaft sensor located on 1995 eclipse?
The camshaft sensor is the same as the crankshaft sensor it is local on the passenger side of the valve cover . And going down to your crankshaft inside the timing belt cover
