The engine block coolant drain plug on 4.3 liter Chevy Blazer is located on the bottom of the engine, near the oil filter. It allows coolant to be completely drained from the block during maintenance.
The 1994 Lincoln Town Car 4.6 liter engine coolant drain plugs can be found on each side of the engine block. There will be a total of four engine coolant drain plugs.
in the block...
Look for the radiator drain it should be on the side of the radiator facing the engine next to the fan.
Check the engine coolant... Is it full? yes coolant level is full
In a 2001 Ford Focus : The 2.0 liter SPI engine and the 2.0 liter Zetec engine use a timing BELT
The engine coolant capacity for the 4.0 liter - OHV engine is ( 12 U.S. quarts ) and for the 4.0 liter - SOHC engine ( 14 U.S. quarts )
There are actually three coolant drain plugs on the 2001 Tundra. Speaking of a 4.7 liter engine, there is one drain plug at the bottom of the driver's side of the radiator. The skid plate/splash shield need to be removed in order to access this. It is a plastic butterfly type and should be easily removed by hand or with the aid of pliers. The other two are located on the driver's side of the engine block. This truck takes over 12 quarts of coolant so these two drain plugs need to be opened in order to completely empty the coolant from the system.
Engine coolant temp circuit high input. The engine coolant temp sensor make be bad.
On a 2003 Ford Focus : The 2.0 liter SPI engine ( SOHC ) and the 2.0 liter Zetec-E engine ( DOHC ) use a timing BELT The 2.3 liter PZEV engine has a timing CHAIN
To bleed the coolant in a 1995 Dodge intrepid locate the drain plug on the underside of the radiator, un plug it and pour new coolant in the system. Close the plug and while the engine is running find the coolant pressure valve and loosen it to relieve pressure. When bubbles stop forming there is no longer air in the system.
The engine coolant temperature sensor and coolant temperature gauge sender are located on the passenger's side of the engine, under the intake manifold.
The 2.0 liter engine in a 2005 Ford Focus has a timing CHAIN Helpfull
The engine oil drain plug torque spec is 19 Ft-lbs.
there is no drain plug in the actual block there is a plug in the lower drivers side of the radiator. to flush the coolant out of the block just, run the motor with the heater on with a water hose in the rad filller until fluid coming out is clear.
A 2000 Chevrolet Silverado with a 5.3 liter engine takes 13.4 quarts of coolant. It is suggest that the coolant be mixed 50/50 with water.
If not discovered in time and run too long, it could cause the seals to fail. Simple remedy - just drain the oil.
Just follow the top radiator hose to the engine and you will see were it clamps onto the thermostat housing. Remove the 2 bolts in the housing and take housing off and the thermostat is right there.Need to drain engine coolant first. BE SURE ENGINE IS COLD.
It's possible that it may not have one.
5W-20 , for the 2.0 liter engine in a 2008 Ford Focus ( according to the Owner Guide )
Yes , look at the 8th " character " of the VIN : " P " is the 2.0 liter SPI engine and " 3 " is the 2.0 liter Zetec engine
The specs for BOTH the 2.0 liter engine and 2.3 liter engine are the same: .051 inch or 0021. mm
2.0 liter engine: 13.2 gal/50 liters --- 2.3 liter engine: 14.0 gal/53 liters
According to the 2002 Ford Focus owners manual : With engine oil filter change : The 2.0 liter SPI engine ( SOHC ) takes ( 4.0 quarts ) The 2.0 liter Zetec engine ( DOHC ) takes ( 4.5 quarts )