answersLogoWhite

0


Best Answer
AnswerI have a 1994 Ranger with the 2.3 motor. There are actually two ignition modules because there are 2 plugs per cylinder for a total of eight. If you open the hood and face the engine it should be on the left hand side of the engine and you should be able to see where all the plug wires plug into it, you can't miss it! =] Good Luck!

This answer is actually for the Coil Packs. The ignition module (there is only one) is located somewhere else in the engine compartment. I still can't find it myself...so far.

it is on your intake

User Avatar

Wiki User

13y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Where is the ignition control module on a 1994 ford ranger 4 cylinder engine?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Where is the ignition and distributor located on a 1990 Chevy Celebrity?

The 1990 Chevy Celebrity engine is distributorless, the ignition is handled by a combination of the engine control module(computer) and the ignition control module. You did not mention which engine the car has. If your car has the 4 cylinder engine the ignition control module is below the intake manifold at the rear of the engine. You can follow the spark plug wires to it. The coils are mounted to the ignition control module. If your car has the V6 the ignition control module is near the starter and again you can follow the spark plug wires to it. Again the coils are mounted to the ignition control module.


In a computer-controlled ignition system the ignition module does what?

The ignition control module acts like the coil and sends the sparks to the correct cylinder when the computer tells it to.


Where is the ignition module on a 1991 Oldsmobile regency?

The Ignition Control Module is on the top left hand side of the engine under the Ignition Coils.


How do I locate the ignition module on a 1990 Chevy Celebrity?

The ICM is located on the passenger side, up under the dashboard. Remove the glove box and you can see it. It will be bolted to the side panel It is held on by 2 bolts, one on top, one on bottom. Disconect battery before removing! The above is the location of the engine control module or computer. If your car has the V6: The ignition control module is mounted to the lower part of the engine block on the radiator side of the engine. If you follow the spark plug wires down they will lead you to it. The coils are bolted to the ignition control module. If your car has the 4 cylinder engine: The ignition control module is below the intake manifold towards the rear of the engine. The spark plug wires will lead you directly to it. The coils are mounted on the ignition control module. It is in a awkward spot to get to.


Where is the ignition control module on 1994 Ford Van E250 6 cylinder?

The only way I can explain it is to follow the wiring from your coil pack (where the spark plugs are) and the wires plug into the ignition module. Also go go www.wrenchead.ca and it has a manual that explains all. if you don't know the answer to a question please keep your moth shut ,please don't waste my time


Where is the ignition module on a 1999 4 cylinder Chevy S 10?

The 1999 Chevy S 10 pickup truck ignition module can be found on the firewall in the engine compartment. The ignition module will be on the drivers side of the firewall.


Where is the ignition control module on an Oldsmobile Alero?

top right rear of engine.


How do you change the ignition control module in a 1989 Chevy Celebrity?

Which engine does your car have?


What is power control module?

The computer that control ignition/ fuel injection, Variable valve timing, cylinder deactivation, etc.


1995 ford f150 4.9 y Control Module - Ignition?

The ignition control module for a 1995 ford f150 is an important part of the drive train. If the module is failing then the engine will run erratically or not start at all.


How do you install a electronic ignition control module?

The electronic ignition control module on an automobile is installed by first locating the unit at the top of the engine. The wiring harness is then disconnected from the original unit an a new module put in its place.


What is obd code P1614?

P1614 - Ignition key/engine control module malfunction