Car Computers and Sensors
1982-1994 Chevy Cavaliers

Where is the knock sensor for a 93 cavalier located?

212223

Top Answer
User Avatar
Wiki User
Answered
2014-10-07 02:15:08
2014-10-07 02:15:08

The knock sensor for the 1993 Chevy Cavalier is located in the back of the motor. It can also be located in the engine valve.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


where is the knock sensor located on 93 cutlass ciera

on a 93 Chevy cavalier ls how to get the crankshaft sensor out of the block also can I remove the oil pan to get to the crankshaft sensor

It doesn't have a knock sensor on the 4.0 L OHV in a 1993 Ranger ( my 1995 Ford Explorer 4.0 L OHV engine doesn't have a knock sensor either )

Cavalier 1985-93 Top of Glove Compartment

on the side of the engine block, on 1994 and later models, there are 2, one on each side on the side of the engine block

On the Ford Probe 93-97 GT's the knock sensor is located underneath the intake manifold. More specifically it is threaded into a fitting on the deck of the engine block in between the heads in the Valley. Shouldn't be too bad if your an experienced mechanic or a mechanically inclined individual. Hope this helps ya out, and good luck.

As far as I know it doesn't have a knock sensor , my 1995 doesn't have one according to the engine wiring schematic in my Haynes book ( I believe in 1996 with the EEC- V system , the 4.0 L - OHV has a knock sensor )

it is located in side the maf actually they use the same sensor housing.

the elictronic control sinsor at on a 93 mercury villager

the knock sensor is a 1.5" round disk with a single wire connected to it. It is located on the bottom driver's side of the engine. Unscrew it from the block and be prepared with a large open-top drain pan to catch all the antifreeze from the block. Use teflon pipe tape on the new sensor to seal the threads.

ESC / Electronic Spark Controll Circuit. and the knock sensor signal.

The temperature sensor on a 93 Olds Cutlass Cierra 3.3 is located on the back of the engine. It is on the intake manifold.

The crankshaft sensor is located on top of the transmission at the passenger side.

crankshaft position sensor wiring eagle vision

The crank sensor is located on the back engine wall in the middle, just under the two coil packs (from where the spark plug wires come). There is a wire harness from the crank sensor to the module which holds the two coil pack. The crank sensor is held into the engine by a single bolt. To see all of this, you have to go under the car. I am having an intermittent no start problem with my 93 Cavalier (it cranks, but no spark at all) and I think the crank sensor is my problem.

Vehicle speed sensor is located on top of the differential on the transmission. Access is from under the car

The IAT sensor is located on the intake manifold air cleaning housing or air duct.

It is mounted on the driver side inner fender close to the battery.

There is not a camshaft sensor on the '93 3.1 Lumina, just a crank sensor on the back side of the engine between the block and the barrel of the transaxle. Easy enough to get to from underneath the car.

I have a 93 Chevy Beretta and mine is located INSIDE my fuel tank so I would look there. in the fuel tank

where is the o2 sensor located on a 1992 Chevy s-10 4.3 ?

At the end of the fuel rail on the intake manifold

The IAT sensor on the 1993 Honda Prelude is located to the right of the intake manifold as you face the engine compartment. It is connected with red and green wiring.

It is located on the intake manifold next to the fuel rail.

It is located inside the ECU and its small and soldered to the circuit board.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.