0
As far as an "Idle adjustment screw"-- remove the filter housing for an easier access, but it's quite visible from the Throttle butterfly side on the Carb--- as far as an "Air Idle-Fuel Mixture" on an '03 XL 883??? Sorry Bud--- there IS NONE-- it's a "Fixed Jet Carburator" and it comes from the factory, with a sealed pug cover, over the adjustment screw, located UNDER the backside of the carb, which unless you're a QUALIFIED Mechanic, or have ALOT of expeience with the H-D carbs now installed at the factory, your best is to leave it alone, and let someone who KNOWS where the plug is actually located,can "DRILL IT OUT" without harming the Air-Idle Screw", and once that's accomplished, you can easily adjust your Carb with a fine screwdriver from underneeth the carb, while it's running. Harley-Davidson, has STRICT Emission regulations, that prohibit the adjustment of that Fuel Mixture Screw, due to E.P.A. Standards--- Hope this helps solve the mystery of "Where's It At" !
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What is the tagline of Harley-Davidson?
Screw it. Let's Ride.
Location of air fuel mixture screw on 1997 harley dyna-super glide?
Location of air fuel mixture screw on 1997 harley dyna-super glideRead more: Location_of_air_fuel_mixture_screw_on_1997_harley_dyna-super_glide
How do you remove seat on harley Davidson road king?
To remove the seat on a Harley Davidson Road King, you must unscrew the Philips head screw that is directly behind the seat. Then, slide the seat and unfasten the hook at the front of it.
Where to check primary fluid on 96 cubic inch harley Davidson?
a small screw on the primary at the bottom near the rear. Looks alot like a primary screw.
How do you adjust idle on a 1998 harley Davidson sportster?
"Idle" can mean two things: idle speed, and idle mixture. Both of these are on the carburettor. Idle speed is adjusted via a screw that is on the throttle control cam. Turning this screw will change the RPMs of the machine at idle. The idle mixture changes the amount of gas that flows during idling, and can be changed by a screw inside a round recession on the bottom of the carb.
How do you remove the seat on a harley Davidson heritage classic?
Unscrew the rear chrome screw on top of fender and a screw on left and right side of seat and pull up and back and remove.
How do you check the transmission fluid in a 1978 fxs harley Davidson lowrider?
there is a Allen screw on the side case fill until it begins to run out.
Why does 2007 Harley Davidson idle so low?
How do you know its low? Idle should be in the 950 to 1050 rpm range. I installed a MSD shift light. Its about the size of your index finger(tubelar in shape) I have a carberated softail so I opened the air/fuel to about two turns. Then I raised the idle to 950. I went back to the air/fuel mixture and found the "sweet" spot after going in and out a few times w/ the mixture screw. When the idle rose, I backed off on the idle screw to about 950 to 1000rpm. .
How do you remove the seat of a 2003 Harley Davidson ultra classic?
Down the back of the queen seat there is a single screw into the fender. You might have to open the topbox for better access. Remove the screw, lift the rear of the seat ad slide backwards and upwards to release the front clip.
How do you remove the seat on Harley Davidson fatboy?
Remove the rear seat screw. Then pull the rear seat to the rear and slightly up. It is held in by two metal tabs that slip under the front seat lip.
Where is the crankcase breather filter located for 1989 Harley-Davidson FLHTC?
If you look at the pushrod side of the motor, the breather screen is located just above the oil pump. There is a large screw/bolt. DO NOT take the one off the oil pump.
What is the setting of mixture screw on throttle body of a 1995 ka24 NISSAN engine?
If it's an EFI engine you do not adjust the mixture screw. The mixture is computer controlled.
