answersLogoWhite

0


Best Answer

The plug hole is near the right belt tensioner just to the outside along the edge of the engine block where the crankshaft position sensor electrical wiring enter the front casing or near where the a/c belt pulley bolts up to the engine block.

User Avatar

Wiki User

โˆ™ 2007-10-26 01:46:10
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: Where is the plug hole to check balance shaft on 1996 Mitsubishi Galant?
Write your answer...
Submit
Related questions

Where is the plug hole to check the balance shaft on 2003 Mitsubishi Galant?

I came across the same question myself. The plug hole is on the radiator side of the engine behind the exhaust. Mine was a size 14 mm bolt.


Where is the speed sensor for 2004 Mitsubishi Galant?

the speed sensor for 2004 Mitsubishi Galant is located on the front case of the transmission output shaft and speed sensor. It is approximately under the hood to the left of the engine.


What does the balance shaft do on a 1999 Mitsubishi Eclipse GST?

It balances the vibrations from the pistons...


Cost of replacing a1995 Mitsubishi galant front crank shaft?

The average cost to replace a 1995 Mitsubishi crankshaft is approximately $2000. The cost is dependent upon the mechanic shop's hourly rate.


Timing chain diagram for a 1986 Mitsubishi 2.0 liter?

It has a belt, not a chain...also has a balance shaft belt


Why is your Mitsubishi vibrating?

Can be tire out of balance, bent wheel, defective tire, broken motor mount, or bent drive shaft.


How many drive belts are on a 2000 Mitsubishi galant 4-cylinder?

timing belt1 silent shaft belt2(behind the timing belt) accesory belt alternator3 powersteering a/c4


What does a balance shaft belt do?

It turns the balance shaft. The balance shaft helps reduce vibration in the motor. It is usually driven by a belt that is connected from the balance shaft to the crank shaft and a tention adjusting wheel used to apply tension to the belt. Hope this helps, Dirk.


Why would a 1988 Mitsubishi Galant 1800 suddenly lose all drive?

Reguardless where it is, the transmission will have to be overhauled. I think probably a shaft snapped or the bolts could have come out of the convertor if it was making noise before it happened.


Does the Oldsmobile Intrigues 3.5 L V6 use a balance shaft?

Yes it does have a balance shaft also known as a silent shaft.


How much is a timimg belt for 2000 galant 4-cylinder?

theres 2,balance shaft and timing belt.mine were $75 for both,i installed them.@ a shop if you can get it done for under $500 your getting a good deal


What driver shaft does Tiger Woods have?

Apparently it is a Mitsubishi Diamana Whiteboard 83 gram shaft.


What are the timing mark setting on a 2001 Mitsubishi Galant 2.4L?

2.4l dohc balance shaft timing mark, crankshaft sprocket timing mark,oil pump timing mark and camshaft TWO timing marks 2.4l sohc balance shft timing mark, crankshaft timing mark, oil pump timing mark and ONE camshaft timing mark. it is complicated only that everymark must be bang on, if not the pistons will hit the valves and YOU get to rebuild engine.


Driveline vibration occurs around 50 mph What SHOULD be checked?

check drive shaft run out and drive shaft balance NEW ANSWER: You need to check the driveshaft U-JOINTS for wear. If you don't find your problem there, Then you may have to get the wheels balanced. Check U-Joints FIRST.


Can you shorten the drive shaft to fit a longer shaft on the transmition?

this requires a drive shaft company that can cut and weld it and balance it after.


What is the shaft in the engine valley for on a 1997 4.3 l Chevy?

That is called a balance shaft.


Balance shaft ford 4.0 sohc?

There is a chain driven balance shaft on the 4.0 L SOHC engine for the 4X4 Ford Explorers / Rangers


At what speed does a drive shaft vibrate?

Drive shafts are balanced to prevent vibration, if yours is doing it you need to check your universal joints, and whether the shaft has been dented or if one of the weights used to balance it has fallen off.


Why does your 1998 Jeep Grand Cherokee Limited vibrate on acceleration at 40-50 mph then again at 52-60mph?

Check the tires for an out of balance issue. Check the u joints in the rear shaft.


Does a balance shaft need to be timed to the crankshaft?

Yes.


How to check crank shaft pulley?

A video instruction guide on how to check a crank shaft pulley can be seen on YouTube. Just type in "How to check crank shaft pulley", click on Search, then play the first video.


What is the best graphite shaft manufactured?

If you are looking to fit a new graphite shaft to your club, I would say it doesn't matter which graphite shaft is the best but it is which one is best for you. Either a Grafalloy or Mitsubishi shaft, but they can be quite expensive.


What causes a car to jugger after changing drive shaft?

Balance


Engine counter balance shaft?

what are counterbalance shafts made from


What would cause a knockingrattling sound from right front tire on a 2001 Mitsubishi eclipse?

bad cv joints check under the car and see if there is a rubber boot on the drive shaft connection to the wheel