Best Answer

It is located on the drivers side of the car on the bottom of the radiator

User Avatar

Wiki User

โˆ™ 2005-04-03 04:20:19
This answer is:
User Avatar

Add your answer:

Earn +5 pts
Q: Where is the radiator draincock on a 1992 Chevy Corsica?
Write your answer...

Related Questions

How do you drain the radiator on a 1992 Chevy Corsica?

The radiator drain on a 1992 Chevy Corsica is located on the bottom, left side of the radiator. It provides a quick and effective way to drain the radiator during maintenance.

Where is the draincock on a 1992 grand am?

Look at the bottom or rear of radiator - may just be a plug

How much time on average is to replace the timing chain on a 1992 Chevy Corsica?

It will take an experience mechanic approximately 8 hours to replace the timing belt in your 1992 Chevy Corsica. The 1992 Chevy Corsica does not have each timing chain, it has a timing belt.

Is there a shut off on the gas tank on a 1992 Chevy Corsica?


Where is the fuel pump on a 1992 Chevy Corsica?

Fuel tank.

What is the firing order for 1992 Chevy Corsica 2.2?


Where is PCV valve located on 1992 Chevy Corsica?

typically in the valve cover.

Where is the Ignition Module located in a 1992 Chevy Corsica?

The 1992 Chevrolet Corsica ignition module can be found on the firewall in the engine compartment. The ignition module will be on the drivers side of the firewall.

How do you install a serpentine belt on a 92 Chevy Corsica?

Put the new serpentine belt on to your 1992 Chevy Corsica pulleys. Push the tensioner pulley to the left to tighten the serpentine belt.

Where is the voltage regulator in a 1992 Chevy Corsica with a 6-cylinder engine?


Where is the fusible link located on a 1992 Chevrolet Corsica?

There are several located in back of radiator close to the starter.

Where is the switch for the brights in a 1992 Chevy Corsica?

on steering wheel colum,the turn switch works it

Where is the power steering pump in a 1992 Chevy Corsica?

Passenger side top of engine, in front of the alternator.

Where is the radiator drain plug for a 1992 Chevy Beretta?

it is on the side almost at the bottom of the radiator..very hard to get too !!!!

What type of transmission fluid does a 1992 Chevy Corsica use?

It uses DEXTRON III automatic trans fluid.

How do you replace a rear brake line on a 1992 Chevy Corsica?

take the old one off, put a new one on.

How do you yurn on high beams on 1992 Chevy Corsica?

The high beam switch is on the blinker. You either flick it back towards you or push it away from you.

Where is the thermostat located on a 1992 Chevy Cavalier?

Usually in housing at engine end of upper radiator hose

Where is the hood latch located on 1992 Chevy blazer s-10?

Front center of radiator support.

Where is the Location of horn on 1992 Chevy truck?

The 1992 Chevrolet truck horn is located in the front of the engine compartment. The horn will be on the right hand side of the radiator.

How do you replace or repair the fuel pump on a 1993 Chevy Corsica 6 cylinder?

located in the fuel tank of a 1992 corsica ,it may be the same for your model if this is so you may need to drop the tank . I would notadvice you to take on this job unless you have to.

Where is the O2 sensor located in a 1992 Chevy Corsica?

You'll find the location for the 4 & 6 cylinder in this pic.

Is the fuel pump on a 1992 Chevy Corsica the same as one from a 1995 Chevy Beretta?

No. The fuel pumps changed in 1993 to a different design, from that point on the pump and sending unit were integrated into one unit. They will not interchange.

Where is the egr valve located on a 1992 Chevy Corsica 4 cylinder?

SIGN UP FOR ALLDATA.COM TO BE SURE. IT IS SO WORTH YOUR TIME AND TROUBLE. T HEMPLE there is no egr valve in a 1992, the manual says so

How do you install a thermostat for 1992 Corsica?

Installing a thermostat on a 1992 Chevrolet Corsica is very easy to do. First, follow the upper radiator hose to the thermostat. Then, you will disconnect the hose and drain it. After the hose is drained, take off the two bolts holding the thermostat housing in place. After the bolts are removed, take the old thermostat out and replace it with a new one.