0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you reset the srs light on a 2000 Honda civic?
These are the instructions out of the Honda Service Manual for 1996-2000 Civics: 1.) Make sure the ignition switch is OFF. 2.) Connect the SCS service connector to the MES connector. Do not use a jumper wire. 3.) Turn the ignition switch ON. 4.) The SRS indicator light comes on for about six second and goes off. Remove the SCS service connector from the MES connector within 4 seconds after the SRS indicator light went off. 5.) The SRS indicator light comes on again. Reconnect the SCS service connector to the MES connector within 4 seconds after the SRS indicator light comes on. 6.) The SRS indicator light goes off. Remove the SCS service connector from the MES connector within 4 seconds. 7.) The SRS indicator light indicates that the memory is erased by blinking two times. 8.) Turn the ignition swith OFF, and wait for ten seconds. Ok first you're asking what the SCS service connector is. Basically it's a jumper wire. It just has a connector so you can easily connect and disconnect it. You can in fact you a jumper wire. It just might make it a little more difficult. Now you want to know where there MES connector is. It's a yellow 2 wire connector located underneath the dashboard near the fuse panel.
You have a 1997 Honda civic and its srs light keeps turned on you want to know that how can you reset the srs light on?
These are the instructions out of the Honda Service Manual for 1996-2000 Civics:1.) Make sure the ignition switch is OFF.2.) Connect the SCS service connector to the MES connector. Do not use a jumper wire.3.) Turn the ignition switch ON.4.) The SRS indicator light comes on for about six second and goes off. Remove the SCS service connector from the MES connector within 4 seconds after the SRS indicator light went off.5.) The SRS indicator light comes on again. Reconnect the SCS service connector to the MES connector within 4 seconds after the SRS indicator light comes on.6.) The SRS indicator light goes off. Remove the SCS service connector from the MES connector within 4 seconds.7.) The SRS indicator light indicates that the memory is erased by blinking two times.8.) Turn the ignition swith OFF, and wait for ten seconds.Ok first you're asking what the SCS service connector is. Basically it's a jumper wire. It just has a connector so you can easily connect and disconnect it. You can in fact you a jumper wire. It just might make it a little more difficult.Now you want to know where there MES connector is. It's a yellow 2 wire connector located underneath the dashboard near the fuse panel.
How do you reset the SRS light on a 96 Honda Civic Do the same procedures used for 99 and up models work?
i had the same problem on my 97 Honda civic lx. the check engin elight came on adn i called my dealor(aka my best friend) he said just unplug the battery for like 2 min or so and the brain wil restet itself. This is incorrect. Yes the procedure is the same for 1996-2000. See them below: These are the instructions out of the Honda Service Manual for 1996-2000 Civics: 1.) Make sure the ignition switch is OFF. 2.) Connect the SCS service connector to the MES connector. Do not use a jumper wire. 3.) Turn the ignition switch ON. 4.) The SRS indicator light comes on for about six second and goes off. Remove the SCS service connector from the MES connector within 4 seconds after the SRS indicator light went off. 5.) The SRS indicator light comes on again. Reconnect the SCS service connector to the MES connector within 4 seconds after the SRS indicator light comes on. 6.) The SRS indicator light goes off. Remove the SCS service connector from the MES connector within 4 seconds. 7.) The SRS indicator light indicates that the memory is erased by blinking two times. 8.) Turn the ignition swith OFF, and wait for ten seconds. Ok first you're asking what the SCS service connector is. Basically it's a jumper wire. It just has a connector so you can easily connect and disconnect it. You can in fact you a jumper wire. It just might make it a little more difficult. Now you want to know where there MES connector is. It's a yellow 2 wire connector located underneath the dashboard near the fuse panel.
How do you reset the SRS module commonly named computer on Honda civic Accord and prelude?
You have a problem with the Air Bag system, "Supplemental Restraint System". This is not a DIY repair. Serious injury can occur, or you may disable the SRS entirely, or cause it to deploy prematurely. Take it to the dealer for repair, ASAP. This is extremely good advice. If the SRS light is on, DO NOT attempt to fix it. Besides that you need a very expensive scanning tool to find out why the light is on in the first place. Tinkering with an air bag is system is very dangerous. Take it to your dealer. True that it is always best to have it checked out, but you do NOT need an expensive tool to figure out why it was triggered. Just an SCS service connector ($10) or a jumper wire. You connect them to the service connector beneath the dash and the SRS light will blink the Error code. Here is how to reset the light: These are the instructions out of the Honda Service Manual for 1996-2000 Civics: 1.) Make sure the ignition switch is OFF. 2.) Connect the SCS service connector to the MES connector. Do not use a jumper wire. 3.) Turn the ignition switch ON. 4.) The SRS indicator light comes on for about six second and goes off. Remove the SCS service connector from the MES connector within 4 seconds after the SRS indicator light went off. 5.) The SRS indicator light comes on again. Reconnect the SCS service connector to the MES connector within 4 seconds after the SRS indicator light comes on. 6.) The SRS indicator light goes off. Remove the SCS service connector from the MES connector within 4 seconds. 7.) The SRS indicator light indicates that the memory is erased by blinking two times. 8.) Turn the ignition swith OFF, and wait for ten seconds. Ok first you're asking what the SCS service connector is. Basically it's a jumper wire. It just has a connector so you can easily connect and disconnect it. You can in fact you a jumper wire. It just might make it a little more difficult. Now you want to know where there MES connector is. It's a yellow 2 wire connector located underneath the dashboard near the fuse panel.
Where do you connect the OBD on a 1990 Honda Accord?
In 1990, OBDI was still in use, not OBDII. OBDI did not have a standardized connector. You will probably need to activate the SCS mode of the PGM-FI and count flashes of LEDs on the PGM-FI module under the seat to get codes.
When was SCS Films created?
SCS Films was created in 1992.
Where can one purchase SCS furniture?
A good place to buy SCS furniture would be at the SCS store in Hull's St. Andrews' Quay in the UK. SCS Furniture Enterprises, Inc. is located in Martinez, Georgia and is a good place to purchase SCS furniture in the U.S.
What does the label SCS mean in Shurley?
SCS means sofas, couches and setees.
In what year did Steelcase Inc - SCS - have its IPO?
Steelcase Inc. (SCS)had its IPO in 1998.
Will a scs scooter clamp fit with threadless forks?
yes, scs is meant for thread less forks.
What does the sofa company SCS stand for?
SCS stand for Sofa Carpet Specialist.
Can you use mgp batwing bars with scs?
Yes im running them with a pheonix smooth scs its really good
