0
Where is the thermostat on a 2001 grand am and how hard is it to change?
Wiki User
∙ 16y ago
The thermostat is to the right (drivers side) of your engine just under the throttle body (where your flexible hose meets the engine from your air filter). It is can be found by looking at where the hose comes off the top right side of your rad and runs to the engine. Where this attaches to the engine is where your thermostat is located right under that metal flange that bolts on to the motor. It is a bit of a pain to get to but easy enough to change.
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
How do you replace a thermostat on a 2001 BMW 325I?
is in hard to replace a thermostat on a 2001 bmw 325i
Where is the thermostat located on a 2002 Pontiac Grand Am?
It is located directly under the throttel body.AnswerWhere is the thermostat on a 2002 Pontiac Grand Am?" Answerwhere is the thermostat on a 2000 Pontiac grand am Instructions on how to change a thermo..Hello, this page has instructions on how to install a new thermostat on a 99+ Grand Am. Also, not listed on the page as an instruction but something I did when changing the thermostat was to take off the throttle body which made getting to the inlet manifold bolts much easier. The bottom bolt was particulary hard to get too, the top bolt was not too bad. Good Luck. http://www.grandamgt.com/thermostat-pfyc.HTML
How hard it is to change the thermostat on a 2002 Chevrolet Malibu?
It is not hard if you have the proper tools. Drain the radiator and remove the upper hose at the engine. Remove the thermostat housing and install the thermostat. Clean the surfaces and install the new thermostat.
How do you replace the thermostat on a 1996 grand marquis?
Replacing the thermostat on a 1996 Grand Marquis is not very hard. First, follow the upper radiator hose to find the thermostat. Then disconnect the hose and drain it. After the hose is drained, remove the bolts holing the thermostat housing in place. Take the old thermostat out and replace with a new one.
Installing a thermostat in Chevy impala 2001 3.4l?
Very hard to get to as it's under the throttle body and you almost have to take it off to be able to get to the 2 bolts to take the thermostat out.
How do you change the thermostat on a 2001 Mercury Villager 3.3 engine?
the thermostat is located behind the timing bet cowling. it is a bear to get off. i changed the timing belt and everything in there when i got it off. too hard to get off to have to do the job twice. the probem is that you cant get to the bolts and there is about 9 of them. i also changed the water pump.
How hard is it to change a vacuum hose and where is it on a 96 Grand Am GT?
Its not very hard to change a vacum hose. I can't tell you where it's at because there are about 20 different ones
Where is the thermostat located on the vauxhall combo 1997 and how hard is it to change?
Its very easy. two bolts but you will need to remove the batt and just follow the large hose from the radiator to the engine and that casing will be the thermostat
Which oil filter is best for 2001 Dodge Grand Caravan?
It's hard to beat a Wix filter for any application
You replaced the thermostat in your 2001 Chevy venture but the van is still overheating the top radiator hose is hard and hot to the touch like the thermostat is not opening up please advise?
The top radiator hose is above the thermostat. If the top radiator hose is hot, the thermostat is opening. The thermostat is not the problem. Perhaps the radiator is clogged up or the water pump is bad. Look elsewhere.
Where is the thermostat located on a 1992 Pontiac Grand AM SE Quad 4?
The thermostat is located on the driver side of the engine just below the cam pulley. (The one with the power steering pump belt.) You just have to follow the top rad hose. P.S. Its hard to get at.
How do you change a blower motor resister for a 2001 Pontiac grand am se?
It isn't hard to do, just hard to get to sometimes. It will be in the blower housing somewhere. it will have several wires going to it. Probably four or more. The resistor itself is usually held on by two screws. remove them and replace it with the new unit. not too bad.
