0
Where is the throttle lever and throttle cable found on a 1994 ford explorer?
Wiki User
∙ 16y ago
On my 1994 Mazda Navajo, which should be the same as an Explorer, their is a black plastic cover with 3 bolts on top of the engine. When you remove the cover the throttle and cruise control cables attach to the throttle lever there. My throttle is sticking but the problem seems to be where the cable attaches to the pedal.
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
Why is the transmission shifting late?
The transmission shifting is late because the kick-down cable needs to be adjusted. The kick-down cable is usually found on the throttle lever with the throttle cable.
How do you lubricate the throttle or TV lever ball studs on a 1998 ford explorer?
How do you lubricate the throttle kickdown or TV lever ball studs?
Where is carburetor on push lawn mower?
Move your throttle lever back and forth and be looking at your engine. The other end of that cable (which will be moving as you move the throttle lever) is your carburator
Where is the TPS on an 88 Chevy Celebrity?
It is attached to the throttle body exactly opposite the cam/lever with the cable(s) on it.
Where can you find the throttle position sensor in a 1993 Oldsmobile cierra cutlass?
The Throttle Position Sensor (TPS Sensor) is located underneath the air intake< right below the Idle Control Valve. If your new, Find where your throttle cable hooks up & its right there. Its on the throttle body. When you follow the throttle cable, you will see it go to a lever that turns a shaft. The TPS is on the opposite end of the shaft.
How do you adjust idle on a 2001 gsxr 600?
step one: prop the fuel tank up to access the throttle lever assembly (left side) step two: trace your throttle cable down to where they go around the throttle lever (more like a pulley) twist the throttle, you'll see this lever rotate step three: locate the idle adjuster screw, its a small stop screw that keeps the throttle lever from turning completely to the full-close position. step four: by turning this screw in, the idle rpm should increase. sorry im no mechanic, but thi
How do you replace a transmission cable for a 1989 eagle premier?
There are two cables. One is the Throttle valve (TV) cable and that should go from the throttle linkage to the transmission. It will pop off the throttle arm and there is one bolt holding the cable housing to the transmission. take it out the bolt and unhook the linkage and replace the cable making sure to snap it back on at the throttle arm. The other cable is the for shifting and it should attach to a lever arm on the side of your transmission and go to the shifter linkage. If you are under the car and have someone shift with the car off you will see the the arm moving disconnect it from both ends of the cable and replace.
What is causing long shifts in your 1997 grand Cherokee tranny?
clutchs in tranny are going bad, bye a new or remanufactured tranny to put in it, it is better than haveing it rebuilt It could also be the spring on the throttle valve being broken or installed in corectly. It is mounted on the side of trans. follow the cable from throttle body to transmission the spring should pull on the lever away from throttle body. ot he cable is not ajusted properly. look for ajustments for the tv "throttle valve"cable.
Where is the throttle position sensor on a 2003 5.3 vortec?
Mounted to the throttle body. Opposite side of the throttle lever.
How do you set the idle on a 1997 Honda Fourtrax 300?
if it is anything like a polaris, check the throttle cable comming out of the throttle lever on the handle bar, there should be a spot on the cable that the rubber will pull apart and you can turn it in or out. dont do what i did though, turned it up too high and when i started it, it was in gear and drove into the side of my truck, lol
Lawn mower will not shut off?
The kill switch wire is broken or has come loose. If it is a push mower, look at the end of the throttle cable where it touches ground when the lever is in the OFF position. If it is a riding lawn mower, follow the wires from the ignition switch, you will find a disconnection someplace near ground (by the throttle cable bracket on my rider).
How do you adjust tv cable on a gm th125 transmission?
-Depress and hold down metal re-adjust tab at engine end of T.V. cable. -Move slider until it stops against fitting, then release re-adjust tab. -Rotate throttle lever to its "full travel position". -The slider must move (ratchet) toward the lever when the lever is rotated to its "full travel position".
