0
Negative battery or jump start post.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Why not clamp negative clamp to battery?
Because there may be a spark when you connect a jumper cable negative clamp to the battery post which can cause an explosion. Batteries emit hydrogen gas which is very volitive. Always connect the negative clamp to the engine or another ground point on the vehicle.
How do you jump a battery in a Mercedes?
To jump a battery is exactly the same as you would jump start any other cars in the world. 1. Connect the jumper cable positive clamp (Red color) to the positive post of the dead battery. 2. Connect the jumper cable negative clamp (Black color) to the negative post of the dead battery. 3. Connect the other jumper cable positive clamp (Red color) to the positive post of a good battery. 4. Connect the other jumper cable negative clamp (Black color) to the negative post of a good battery. 5. Start your Mercedes. 6. Reverse the 1-4 steps when the car starts successfully. Note: Step 3, and 4 could be a good strong battery, or a battery on a running car. weijen_hsu@yahoo.com
What hint does the author of how to jump start a car battery give for remembering that you should connect the positive clamp onto the battery before the negative clamp?
you should give positive feedback to your friend Marvin about his tuba recital before negative - apex
What are the steps if one wants to jump a car battery?
Get a working vehicle. Bring it to the disabled vehicle Verify that both the dead battery and the rescue battery have the "same" voltage.Verify that both the dead battery and the rescue battery have the "same" voltage.Turn off both engines, Turn off the headlights, wipers, radios, and all accessories on both cars, Untangle and unwind the jumper cables, Visually check both batteries for cracks, leaks, and damage,Connect a red clamp "first" to the positive post on the dead battery, Connect a black clamp to the negative post of the good battery, Connect the only remaining clamp, Start the working vehicle so it can be charging its own battery and the dead one,Let it idle for approx,Try to start the disabled vehicle,Remove the jumper cables
How do you replace battery in 2002 buick regal?
Disconnect the Regal battery cables. Find the battery clamp then remove it. Lift the battery out, then put the new one in. install the clamp, then connect the battery cables.
How do you change the battery on a 1992 Toyota Camry?
disconnect the battery cables. find the battery clamp and remove it. Lift the battery out, then set then new one in place. Install the clamp, then connect the battery cables.
When removing the battery leads from the terminals you do what first?
Disconnect the negative - terminal first, then the positive + terminal. Unfasten the battery hold down clamp. When reinstalling the terminal connections connect the positive terminal first.
Your Porsche battery is dead and located in your garage What is the best way to jump without damage?
The following comments consider the clamping procedure only. There are general safety procedures for this activity to be aware regardless of car type. 1990 Porsche manual page 103 shows emergency starting with jumper cables. Diagram shows first; connect positive cable clamp to positive post discharged bat. , second; positive cable clamp to booster bat. positive post ., third, connect negative cable clamp to negative post booster bat., lastly; connect negative cable clamp to bare metal on car with discharged battery. Read instructions on your cables.
How do you change a battery on a Honda pacific coast?
Lift the seat up all the way and on the right hand side you will see the battery. You will need a battery charger with relatively small clamps. Pull the red plastic cover back from the hot terminal and connect the hot clamp from the battery charger. Then connect the ground clamp to the ground terminal on the battery. Be sure to set your battery charger on 12 volts
How do you Change battery for 2003 Mercury Mountaineer?
Disconnect the negative battery cable and then remove the positive cableRemove the battery heat shieldRemove the battery hold-down clamp boltLift out battery
How do you jumb start a car?
I think you mean jump start, but here is how: You need 1 car that works and jumper cables (can be found at local auto parts store) Open both hoods and locate the batteries on both cars and on each battery there is a positive terminal and a negative terminal Turn on the car that starts and position it so the battery is close to the battery of the car that needs the "jump" On the battery there are 2 terminals (where the electric comes from). The positive has a + and the negative has a -, connect the red clamp (on jumper cable) to the + and the black clamp to the - (some cars have a red plastic cover you must remove on the positive (+) terminal) Whatever you do DO NOT allow the other ends of the cables to toutch, a dangerous situation and/or damage to car may result Now connect the red clamp on the other end to the positive+ terminal and the black clamp to the negative - terminal. POSITIVE CONNECTS TO POSITIVE AND NEGATIVE CONNECTS TO NEGATIVE Try starting car. Tip: if car still does not have enough power to start you can try cleaning the battery post and/or digging the jumper cable clamps into them for a better connection
What hint does the author of how to jump start a car battery give for remebering that you should connect the positive clamp onto the battery before the negaticve clamp?
Think of the phrase black as night and the fact that night starts with an n
