0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is best place to put a jack under 1975 Jeep CJ5?
Jacks or jackstands should be placed under the frame.
Where do you put jackstands under Honda del sol?
Look under the car and you will see what appears to be a frame built into the floor pan. Place the jack stands under those frame rails.
When changing front shocks on a 91 2wd Ranger where should you place your jack stand and where should I put my hydraulic floor jack to initialy lift the front end?
You need to place the floor jack under the actual beam of the car frame. This is where 2 jacks may have to be put into play. You will need to jack up the car high enough to be able to release the old shocks from their bases. You may have to put a jack on blocks to jack the car high enough to achieve this. Put your stands on very stable blocks under the frame as well.
Where is the best place to put jack stands when lifting the front of a 1993 Oldsmobile Delta 88?
there is a place for the jack on the sub frame. it looks like a thin lip of metal that runs all the way down the sub frame. look for where it gets thicker and put your jack stand under it, but get it as close to the front of the car as you can.
Where do you jack the front end up for tire changing?
if its a 4 wheel drive vehicle just put jack under chunk on front axle. if 2 wheel drive then put jack on metal A shaped brace that goes from frame and shock to each wheel.
Where do you place jack to change front tire?
You should put the jack on the frame like it says in the instruction manual, but its hard to do from there i would suggest that you should put it on the axel, it may or may not work, i have not tried it, but its really hard to push the jack up on the frame.
Where can you put a jack under a 2009 dodge charger?
The safest spot to jack for normal tire changes is the cutouts just behind the front wheels and just in front of the rears. There are also frame jack-points a bit deeper under the car, four in the front but just the differential case itself in the rear. Either way, don't put anything you'd like to keep in it's current condition under the car when it's just supported by just a jack itself - use jack-stands.
2005 viper. Is there a floor jack made to lift it safely and were would a safe lift point be?
Yes any racing Aluminum low profile jack that you can keep in your garage will work. Make certain the jack will hold at least 5000 lbs . driver your can onto two 2x4's at least 2 feet long as this will raise your car high enough to put the jack under your car. Jack under the engine cradle up front this is the 2 x 3 inch square tubing frame section under your engine (NOT any aluminum parts that would be your oil pan about $ 1400) Always use jack stands for safety. Again when you lower your car put eh 2x4 back under the center of the tires so you can get the jack back out! If your rear approach is in effect, just inbound from the exhaust hole is the frame, jack here and a jack stand under both sides of each frame rail. Usually lightly shake the car to make CERTAIN that you put the stands in place properly for safety. Life is too short to be crushed by a car even a Viper ! Viper Racer
How do you jack up the front end on a Chevy truck?
Well its kinda complicated. You see first you need a hydraulic jack to raise the front section of the truck. you need to chock the back wheels or set the parking brake. You place the jack under the front crossmember support and start pumping the jack. If you are going to get underneath the truck, put jackstands under the frame and lower the jack onto the jackstands. Then wholla. Jacked up
How do you replace motor mounts in 1989 mustang 5.0 lx?
this is best if car is in the air. then put a jack under the engine/ crankshaft pully is where i put it on mine. then unbolt the mounts from the frame, then the bolts to the engine. and have the engine lifted enought to remove the old mounts and put the new ones in.
What is the frame for a 89-90 Chevy Caprice?
there is no frame its a unibody meaning frame is enginered into the body they basically just thickened some stuff up and called it a day they just put like half a frame on each side along the rockers (where you put the OEM jack and along there is the magic behind it all)
How do you change the front and rear sway bars on a 95 windstar lx?
to do the frt one's put a jack under the sub frame and then undo the sway bar links remove the two rear sub frame bolts and let the jack down slowly you may have to unhook the exhaust at the flex pipe remove the four bolts from the sway bar bushings and the bar should come out.
