0
Where would I attach the negative ground cable in a car if I need to use the battery charger?
Wiki User
∙ 11y ago
The negative lead of the battery charger can be connected to either the battery negative terminal/post, the alternator case, or a known good engine or chassis ground. Note, if the lead is placed on a painted surface, high resistance will occur and the system will not charge.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Where on the battery do you plug the charger into?
A typical car battery charger will plug into a wall outlet. The end that connects to the battery itself generally has aligator clips on two different leads. The black one is your ground or negative, the red is your positive. Attach each clip to its corrisponfing battery post. Follow the directions for your specific charger to ensure your charge the battery properly.
How do you connect battery charger cables to charge the battery in the car?
You connect the cables BEFORE you plug in or turn on the charger. Positive (red) to battery positive first, then negative (black) to battery ground. Then you turn on your charger and set the timer.
How do you hook up a charger to a 98 Monte Carlo battery?
A charger is hooked to a 98 Monte Carlo battery by attaching the positive lead to the positive battery post and the negative lead to a strong ground. The charger is set to the desired rate and plugged in.
How do you charge a 12 volt car motorcycle or boat battery with a battery charger?
red wire or clamp to positive (+) post of batteryblack wire or clamp to negative (-) post of batteryset charger to 12 volts (if more than one setting available)plug charger into wall socketlet charge for 12 hoursThere is a danger of exploding the hydrogen and oxygen gases that are given off from a fully charged battery, so remember Don't Smoke whilst doing the above!Also, it not safe or in any way good practice just to put both of the charger cables directly onto the battery terminals.This is the safe way to do it: first clip the +ve cable onto the +ve battery terminal. Then clip the -ve cable to a good "Ground" point somewhere on the vehicle's bodywork, at least a yard or a metre away from the battery.When you want to remove the cable, do this: first unclip the -ve cable from the "Ground" point; only then unclip the +ve cable from the +ve battery terminal.Doing it all that way helps to avoid sparks over the battery's air vents when you attach or detach the +ve cable from the battery.Always remember: NO SMOKING!Always for safety sake!!!!! Wear safety googles and cover exposed skin before putting any battery on a charger, with that being said be sure to put the positive(red or larger terminal) on first, then clip on the negative(black or smaller terminal) last, also to avoid sparks and possible explosion of the battery acid in your face etc. be sure the battery charger is not powered up before you hook it to the battery, in other words keep the charger unplugged before you clip up to the battery in question being charged.Also: Try to be charging in a well ventilated area to help avoid the possibility of explosive fumes meeting up with unexpected sparks Work smart, work safely!!!More detailsEach type of battery charger is different, they are not all the same. Each unit should come with a set of instructions specific to that model and also some important safety precautions.First check fluid level in battery. Then with charger turned off, connect positive cable, (the red one) to the positive side of the battery. Then connect negative charger cable (the black one) to the negative, (ground) side of the battery. then select how many amps on charger u want to charge at. the lower the charging amps, the slower the battery will charge,but the slower the better, if you have the time. for eg charge at 2 amps and leave all night while charging, remove caps from battery, also you do not need to remove battery from car, but make sure ignition is off and key removed, when battery is charged remove cables black one first then red one.Read the instructions that came with the battery charger to make sure you know how your specific battery charger works.Connect the battery charger to the battery. If the battery is connected to the car, attach the positive (usually red) charging cable to the positive post (usually marked with a plus sign). Then attach the negative (usually black) charging cable to theengine block. Do not connect the negative cable to the negative post while the battery is in the car. If the battery is not connected to the car, attach the positive charging cable to the positive post. Then attach the negative charging cable to the negative post, usually marked with a minus sign.Volt/Amp Selector on control panelTurn the "Volt/Amp Selector" to the appropriate type of battery and amps, and make sure that the correct "Volt" switch is selected for the size of battery.Plug the battery charger into an appropriate outlet. If the cord has a ground, plug it into a grounded outlet. Do not alter the cord in any way.Use the ammeter to measure battery-charging rate.Turn the "Charge Time" to set how long you want to charge the battery. Use the ammeter to measure battery-charging rate. Use the battery test monitor to see if the battery is in working condition.Turn the battery charger off. Unplug the battery charger from the outlet. Turn the "Selector" and the "Charge Time" to "Off."Remove the negative battery charging cable first, then remove the positive charging cable.
On a 12 volt positive ground dc system how do you charge the battery?
You basically just reverse the charger's leads, attaching the positive lead to the `ground side' (chassis) and the negative lead to the negative connection on the battery. I'm assuming of course that you're referring to a British made automobile.
Where does the ground wire go on a car battery?
Negative - (Black) is Ground, Positive + (Red) is Hot. Ground wire goes to Negative (Black) it goes from negative on battery to engine for ground.
Is your 1996 suburban battery a positive or negative ground?
The Suburban has a negative ground system.
Why three wires on battery charger?
If you mean the wires in the battery charger's household AC power cord the three wires are "Hot" or "Live", "Neutral", "Ground".
How do you change a battery on a Honda pacific coast?
Lift the seat up all the way and on the right hand side you will see the battery. You will need a battery charger with relatively small clamps. Pull the red plastic cover back from the hot terminal and connect the hot clamp from the battery charger. Then connect the ground clamp to the ground terminal on the battery. Be sure to set your battery charger on 12 volts
How do you hook the battery charger on a positive ground system?
Connect the positive clip of the charger onto the positive post of the dead battery. If the battery is located inside of a vehicle, connect the positive charger clip to a grounded surface--like an engine block--on the vehicle.
Your 1990 Cadillac Sedan deville 4.5 v8 has a dead battery and the hood release will not release and you need to know how you can open the hood?
I would crawl underneath the vehicle and attach a battery charger (+ Red) directly to the starter center terminal and the other end( black - )to a good ground. This will charge your battery.
How do you jump start a dodge charger srt8?
Hook a jumper cable from the positive end of the donor car to the positive terminal of the Charger, hook a jumper from the negative terminal of the donor car to a spot where you can make ground on the Charger, and have at it. The battery is in the trunk, and there are jump start posts under the hood on the passenger side.
