Smooth clear sound comes from IC and transitor has more loudness and more bass and also consumes more electricity , transistor is good for outdoor used but if u love more loudness then try transistor
The Junction Field Effect Transistor (JFET)exhibits characteristics which often make it more suited to a particular application than the bipolar transistor. Some of these applications are: - High Input Impedance Amplifier - Low-Noise Amplifier - Differential Amplifier - Constant Current Source - Analogue Switch or Gate - Voltage Controlled Resistor
Stop asking homework questions.Class A -Best Audio SoundClass AB - between A and BClass B - (Slight crossover noise)Class C - Best RF Amp
An audio amplifier boosts sound levels. Audio amplifiers typically contain transistors, though the transistors are often packaged inside ICs (Integrated Circuits). A transistor is an electrical device that allows a small amount of voltage or current to trigger a larger level of voltage and/or current. So an amplifier reproduces the sound at a higher amplitude or strength. Of course, there are some tube-type amplifiers that are still in existence. Those are rare and it is hard to find the tubes. Vacuum tubes were what was in use before transistors. There are different types of audio amplifiers. Radios and televisions contain audio amplifiers to be able to drive the speakers. Once the audio signal is extracted from the radio waves and passes out of the detector stage, it is too weak to drive a speaker. Sound boards in computers are capable of driving headphones directly, though not always at a comfortable volume. If you want the volume to be louder, or you want to listen through speakers, you would do best to get a set of amplified speakers. They contain an amplifier inside, and that is why they require batteries or a power cord.
There are many places where someone can buy an AV amplifier. The best place to check would have to be the online website, Amazon. They have them at an affordable price.
No. An amplifier designed for an 8 ohm load works best with an 8 ohm load. You can connect a 4 ohm load to it, but the current rating curve of the amplifier will not match the voltage rating curve, and will will not achieve rated power. Attempting to achieve rated power will result in damage to the amplifier. Look at this mathematically... If the amplifier is rated 100 watts into 8 ohms, then it can produce 28 volts doing so. It will also produce 3.5 amperes at that power. So, when we say the amplifier is rated 100 watts into 8 ohms, we mean that the amplifier is rated 28 volts or 3.5 amperes, whichever comes first. Connect a 4 ohm load to this amplifier, and 3.5 amperes will induce 14 volts and 50 watts. You cannot get 100 watts because that would require 5 amperes and 20 volts, and the amplifier cannot produce 5 amperes.
The genres of music that sound best on an amplifier are Techno,Dance and Trance.
The optical cable would be the best choice.
The Junction Field Effect Transistor (JFET)exhibits characteristics which often make it more suited to a particular application than the bipolar transistor. Some of these applications are: - High Input Impedance Amplifier - Low-Noise Amplifier - Differential Amplifier - Constant Current Source - Analogue Switch or Gate - Voltage Controlled Resistor
Yes if you want the best sound out of it then it is a must.
The factory radio most likely doesn't have RCA jacks in the back, which is what you are going to want to use to hook the amplifier to the stereo to get the best quality sound. Otherwise you are going to have to wire the amplifier to the speaker wires using the high input plug that comes with the amp and you will get poor quality sound out and your subs will not have much bass (that is why it called the high input).
sony ericsson w800i produced high quality sound
nokia x2 best and tomuch sound...
Behringer Europower EPQ2000 Power Amplifier is one of the best power amplifier that has high-quality components and ensures long life. It has several features and variable controls.
It stands for 'Thin Film Transistor' - one of the best quality screens available.
Stop asking homework questions.Class A -Best Audio SoundClass AB - between A and BClass B - (Slight crossover noise)Class C - Best RF Amp
depends on whether you would like calculate or measured results. if you want calculated resulted, then your best bet would be to use an oscilloscope. if you want calculated results, then there are formulas for finding out the voltage, current, impedance, and individual results from each component using the capacitive reactance, voltage, and type of transistor. are you using a summing transistor, inverting amplifying transistor, amplifying transistor, or a different transistor? also are you using DC or AC voltage or current? you need to tell me what type of transistor you are using?
itunes