0
Which way do you turn the bolt on the axle that holds the drum and rotor on?
Wiki User
∙ 13y ago
RIGHTY TIGHTY - LEFTY LOOSY - unless its has backwards threads (left hand)
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How do you repair a broken lug bolt on a 1995 Rodeo?
lug bolts are pressed in to either the axle or rotor from the back. first remove the drum or rotor for easy access, using a punch push the remaining part of the bolt out of its hole, then feed the new one in, you can use a bunch of washers and the lug nut to press it in just keep stacking washers and tightening until the lug is fully set in the axle, a hammer is not recommended
How do you remove rear axle 2003 gmc Yukon?
Remove wheel, Remove drum or disc brake rotor,remove rear differental cover. Remove shaft between the spider gears that is held in by a lock bolt. Shove the axle from the outside toward the differential and remove the "C" clips that hold the axle in inside the diff. and then the axle can be removed.
How do you take the axle out of a Chrysler 8.25?
To remove the axle shaft, first remove the wheel, and brake drum/rotor. Second, remove the differental cover. Third, remove the bolt holding the spider gear shaft, and remove that shaft. Fourth push inward on the axle shaft to remove the horseshoe clip on the inside. The axle shaft will now pull out.
How do you replace a rotor drum assembly on a Dodge 3500 series?
It's either a rotor (disc brake) or drum (Drum brake) either way you have to remove the wheel for both, for drum it takes a firm rap with a dead blow around the side of the drum and then should pull off. For Disc Brakes you remove the caliper and pads the the same goes for the rotor gentle tapping on the back side and it should come free. The rotor is bolted to the inside of th e wheel hub on a 3500. You need to remove the brake caliper, axle shaft, and wheel hub.
How do you change wheel studs?
Is the stud that needs to be replaced in a drum or on a rotor? In either case, remove the drum or rotor from the vehicle. Take a mallet and some type of pin, and drive the broken stud out of the holder. If you know someone with a press have them do it for you. The next step is to get a replace ment stud that is the same size as the old one. Take the replacement stud and place it into the hole where the other stud was removed. Take the nut and turn it so the angled side is facing away from the drum or rotor. State the nut onto the bolt, taking care not to cross thread it. Tighten the nut until it pulls the bolt seat into the hole. Remove the nut and reinstall the drum or rotor onto the vehicle.
How do you get a tire off the axle on a 2001 Chevy prism?
Some basic car knowledge here: - the tire, the rubber donut, sits on a rim - the rim is then bolted to either a brake drum, a brake rotor or possibly a hub. You can't take a tire off the axle, as it isn't attached to it. You can take a tire off the rim, you can take a rim off a brake drum or a hub. And you can take a brake drum or a hub off an axle. Let us know which it is.
How do you replace an axle seal and bearing on a 1993 Ford Crown Victoria?
Assuming rear wheel drive and you're replacing the rear axle seal and bearing with drum brakes: With rear axle off the ground, on stands or blocks and parking brake OFF, remove tire/wheel. Pull brake drum, check for retaining plate that holds bearing, it's usually a 4 bolt square plate near the center of the axle. With the axle off, attach an axle shaft puller to the axle and slide the weight vigorously down the shaft until it pulls off. You will need to take the axle shaft to a shop that has a bearing press so that you can remove the old bearing and install the new one. Many auto parts retailers have a bearing press and won't charge to remove and replace a bearing from the shaft if you buy the parts from them.
How do you get the rear brake drum off a 2005 Toyota Tundra?
There are two holes in the rear brake drum on the face of it that are threaded, they will be across from eachother. Find the correct thread bolt and screw them into the drum. They will push the drum out and away from the axle. Screw them in evenly a little at a time and use a rubber mallet if needed to pound around the drum to help it off. Sorry I am not sure of the proper bolt thread, I just looked through my can of bolts until I found two that fit. Hope that helps! The correct bolt size is M8 x 1.25 thread, I used one 35mm Long.
How to remove wheel drum on 1994 dodge spirit?
The studs are attached to the drum so the easiest thing to do is remove the drum from the axle. Pop of the grease cap, remove the cotter pin and take off the crown nut. The drum should pull of the axle now
Are there Drum or rotor brakes in rear of 2000 explorer?
disc brakes in front and rear ( rotor ) Also , the rear rotors have a small drum on the back of them for small emergency brake shoes
Chevy Malibu Drum Brakes?
On the rear axle only
Why does the back of your car wobble?
The possibilities are, a bad tire with belt separation (most likely), a bent rim or a bent axle. If it only wobbles when the brakes are applied you may have a warped brake rotor or brake drum (which ever applies).
