0
Why can a magnetized screwdriver help to place screws in holes that are hard to reach?
Wiki User
∙ 9y ago
Because it holds the screw straight while you insert it. There is also a 'split blade' screwdriver for this purpose.
Wiki User
∙ 10y ago
Wiki User
∙ 11y agoNo
Add your answer:
Earn +20 pts
Why is it that a magnetised screwdriver can help to place screws in holes that are hard to reach?
The screw will stick to the screwdriver. There is also a tool known as a screw set, it claps on the top of the screw. These have more control of the screw. And you odds of losing the screw are less.
How does screws make work earier?
Screws help by keeping things in place. Only if you have a screwdriver...
How do I remove the radio in a silhouette?
ÊUsing a screwdriver, remove the screws from the center console panel.Pull the panel off,use the screwdriver to remove the screws holding the radio in place, pull the radio out and remove any wiring connections.Ê
How do you replace a rear brake light in a 95 Tahoe?
Open tailgate(s). Look for two plastic caps that cover the screws holding the tail light assm in place. Pry out plastic caps with a flat blade screwdriver and remove the screws you see inside, I think they are Phillips. Remove assm from car, disconnect wiring by turning and pulling. Replace lamps, reassemble in reverse being careful NOT to drop the screws into the taillight assm. Best to tape screws to screwdriver while reassembling to keep screws in place.
How to Replace 1989 gmc front speakers?
Use a dull flat head screwdriver and carefully pry the side closest to you up (farthest away from windshield)enough to see the metal clips going down into the dash, position the screwdriver as close as possible to these metal clips to avoid breaking the plastic that holds these clips on. once you have the metal clips clear then slide the cover away from the windshield, you will see the two slide in clips that hold the front in. To put the covers back on slide the two front clips (closest to windshield) into the holes, then line up the metal clips with their holes and snap them into place gently. To remove the speakers use a stubby Phillips head screwdriver to take out the four screws that hold the speaker down, be sure not to place them on the dash since they will fall into the windshield defroster holes very easily. After the screws are out just pry out the speaker. Installation is the reverse of removal.
How do you replace air filter in 2003 Honda accord?
on the right side of the engine you will see the air box, you will see that it is being held in place by four screws so grab a screwdriver or wrench and remove them, when removed lift towards engine and remove filter, place new filter and reapply screws.
How do you install the front license plate bracket on a Honda Pilot?
The Honda Pilot does not come with pre-drilled holes for a front license plate bracket so first you have to drill the holes. Once the holes are drilled then you can use the screws that came with the bracket to secure it into place.
How do you replace rear lights on a Kia sorrento?
tools needed: Phillips head screwdriver, Flat head screw driver. Open the door on the back of the vehicle. Locate the screws that hold the Taillights in place. Using the Flathead screwdriver, pry the taillight directly toward the rear of the car ever so gently until it pops loose. replace the bulb. when putting the light housing assembly back in place, give it a gentle but firm tap to seat it in place. Put the screws back in.
Where is the 4x4 control module located on a 1988 Bronco?
It is located under the grill on the dash of the vehicle. It is held in place with Phillips head screws and you will need a very short screwdriver or a ratcheting bit.
How do you put alternator belt on ford galaxy?
TAKE THE TENSION OFF BY SECUREING A WRENCH ON THE NIB AT TOP OF TENSIONER . THERE ARE TWO HOLES TO PUT A FINE SCREWDRIVER . THAT WILL HOLD IT IN PLACE WHILE YOU ARE WORKING ON IT
How do you remove the license place light assembly on a 2005 mustang?
If you look under were the plate is the light is held in by 2 plastic screws just get a flathead screwdriver and separate them and light assembly will come right out
How do attach a front license plate to a 2005 Bonneville?
To attach a front license plate to a 2005 Bonneville, simply place bolts through the plate and through the bumper holes in the front bumper. If no holes exist, you can use self-tapping screws to create them.
