0
Why do you have to have your flywheel resurfaced when you change your clutch on a Chevy s-10?
Wiki User
∙ 17y ago
This just ensures that the fly wheel is perfectly even and to remove any warped spots . The clutch needs to be mated at even distance or the clutch will be prematurly burned out. Also if the flywheel is warped it can cause the clutch to slip as it is used.
Wiki User
∙ 17y ago
Add your answer:
Earn +20 pts
How many labor hours for a flywheel on a 96 Chevy truck?
It will take and experience mechanic six hours to replace your 1996 Chevy truck flywheel. A novice mechanic will take several more hours.
How do you fix a flywheel on a 350 Chevy?
About the only thing that can go wrong with a flywheel is for it to crack or loose teeth. In either case, you replace it, not repair.
I have to push the clutch all the way down to start my 82 Chevy truck why?
This is a safety feature.
How do you change th alternator on a2006 Chevy hhr?
how do you change the alternator on a chevy 2006 hhr
Does a 350 Chevy and 327 Chevy take the same starter?
Sometimes. There are two common bolt patterns of Chevy starters, and two common flywheel diameters. Many blocks have both bolt patterns. If the starter bolts up to the block and engages the ring gear without binding, it fits.
Can you reuse flywheel clutch torque bolts for Chevy 350?
i have replaced my clutch to 10.5 diemter ,can i re use the morso flywheel/clutch bolts
Where is the clutch on a 1988 Chevy truck?
It is bolted to the flywheel on your transmission
What are flywheel clutch torque settings for Chevy 350?
65ft lbs
How do you change a flywheel on a Chevy truck?
How do you change a flywheel on a Chevy truck? You can remove either the engine or the trans. Once you have either removed just remove the bolts holding the flywheel in place.
How do you change a Chevy 350 flywheel?
remove the enigine and then take out flywheel bolts
Change flywheel on 1997 Chevy ck?
You'll need to either pull the transmission or the engine to be able to get to the flywheel. Once the flywheel is exposed, it's just a few bolts and it falls off in your hands. BTW, when you put the flywheel back on, I would strongly recommend using Locktite or equivalent to keep the bolts from working loose. A flywheel should always be resurfaced before putting it back, unless it's a new flywheel, in which case you should make sure to remove all of the protective oil.
Can you use a 1986 Trans Am 5 speed tranny with a 1974 Chevy 350 motor What flywheel would you have to use?
You have to use the flywheel for the 1974 engine and the clutch plate for the Trans Am.
When do you need to shim the flywheel on a 91 Chevy?
If the clutch system uses hydraulics, the flywheel should be shimmed the amount that was removed. Removing material from the flywheel moves the pressure plate away from the throwout bearing by the amount that was removed.
How do you change the flywheel on a 2000 Chevrolet Cavalier?
You will need to pull either the transmission or the engine. The flywheel is attached to the back of the engine, to the output side of the crankshaft. If it is a manual transmission, you will need to align the clutch to the pilot bearing before you tighten the pressure-plate.
How do you adjust a hydraulic clutch for a Chevy Cheyenne?
You can't, It is not ajustable.The clutch slave cylinder may be bad CHECK. could have air in system. BLEED system are the clutch parts are worn out. Replace clutch parts and TURN flywheel.
How do you change the clutch on a 1999 cavalier?
Changing the clutch on a 1999 Chevy Cavalier requires remove of the transmission. Once the unit is dropped. Access and loosen the flywheel bolts. Then remove the clutch dish bolts. Pull the clutch off. Installation and reversal of the removal, just be sure the properly bleed the clutch system.
How do you change a fly wheel on a 1990 Chevy silverado 2500?
The transmission must be removed to change the flywheel.
