0
Why does my Amplifier receiver drop the sound once in a while for no reason?
Wiki User
∙ 13y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is meant by external gain of amplifier?
The internal gain of an amplifier is the gain or the amplification factor of the transistor used in it....................it is internal because it is fixed for transistors while manufacturing..................
What is the definition of amplifier?
If you are speaking of the radio amplifier, it takes the low powered signals from the radio and increases them for output to the speakers. Amplifiers usually have some provision or internal programming for splitting the signal so lower frequencies go to subwoofer and midbass speakers while higher frequencies go to tweeters.
Can you use transformer in place of amplifier?
A transformer is a passive device while an amplifier is an active device. a transformer can amplify voltage but never power WHILE AN AMPLIFIER CAN amplify power's can you use it sure withing the limitation of the transformer and only to amplify volts.
What are Pre-Amp outputs?
They are RCA type connectors on the back of your Head Unit (Radio). There are 2 connections, usually blue and white, the cord for this has the same connectors on both ends. The Pre-Amp outputs are a direct line for the Signal from your Head Unit to go directly to an Amplifier (you will see similar connections on your Amplifier as you see on the back of your Head Unit), so when you run speaker wire from your Amplifier, the speakers will play the sound (Music) your Head Unit is producing no matter if its from the CD or FM/AM tuner or AUX input like from an I-Pod.Another AnswerA pre-amplifier, which is also known as a 'control unit', a high-fidelity unit which is separate from, but which must be used together with, a 'power amplifier'.Pre-amplifier/power amplifier units are normally regarded as 'high end' equipment and tend to be very expensive. The pre-amplifier unit is equipped with inputs for phono, CD-player, tuner, and various other auxiliary units and (usually) provides a single pair (right- and left-channels) audio outputs for connection to the power amplifier. The pre-amplifier is the unit which provides the volume control, tone controls, filters, etc., while the power amplifier simply amplifies the output from the pre-amplifier unit. The output usually takes the form of a pair of RCA connectors, usually colour coded white and red.Some 'home theatre' amplifiers provide a 'pre-amplifier' output, which bypasses its internal power amplifier, for the purpose of adding external power amplifiers, if desired.
Why you do not use capacitor in a transistor as switch?
The capacitor is there to block any dc voltage that might be applied to the input terminal, which could cause damage or upset the biassing if it was allowed through to the base.
Does the quality of my receiver affect the sound quality of my car's subwoofer?
While a good receiver is important, the subwoofer is really in control of sound quality.
How do you get dolby 5.1 sound while watching tv on computer to be 5.1 sound on receiver?
You will need a sound card with a digital output (coaxial or optical) or a sound card with surround audio outputs and a receiver with 5.1 analog inputs to make it work.
How clear is the sound?
Sound can be very clear, but it depends on the speaker and receiver. Quality systems, while expensive, can produce incredible clarity.
How clear is the?
Sound can be very clear, but it depends on the speaker and receiver. Quality systems, while expensive, can produce incredible clarity.
Whats the main difference between small signal amplifier and large signal amplifier?
1.Small signal amplifier can be designed easily using s parameter while large signal amplifier not.
Why might a mast-mounted amplifier be preferable to an amplifier right at the TV set?
The mast mounted amplifier will amplify only what is coming out of the antenna, while a set located amplifier will also amplify any noise that was induced in the lines between the mast and the set.
What is the responsibility of the receiver?
sender is to deliver or give message while the receiver is to receive a message from the giver or sender.
What is internal gain of amplifier?
The internal gain of an amplifier is the gain or the amplification factor of the transistor used in it....................it is internal because it is fixed for transistors while manufacturing..................
What is meant by external gain of amplifier?
The internal gain of an amplifier is the gain or the amplification factor of the transistor used in it....................it is internal because it is fixed for transistors while manufacturing..................
What is the responsibility of sender and receiver?
sender is to deliver or give message while the receiver is to receive a message from the giver or sender.
How to install a stereo in a car?
Installing a stereo in a car may look like a task that is best left up to the professionals, but in reality, the task is simpler than it looks. With a number of installation kits that simplify the installation process, it’s easy to install a stereo in little to no time at all. If you choose not to use a kit, then while there will be a bit more work involved in the installation, it is not completely impossible for someone to do it on their own. There are several components that make up car’s stereo system. These include the speakers, the receiver unit and the amplifier. The receiver controls all of the aspects of the stereo system’s operation, receiving FM and AM signals while controlling the volume and tone of the sound. The receiver itself can provide sound to the speakers, but most receivers and many factory installed units don’t have enough power to properly deliver that signal, requiring the use of an external amplifier. This is why many vehicles have an amplifier installed in addition to a receiver. The speakers, of course, deliver sound to the interior of the car. The average automobile will have anywhere from three to eight, depending on how high-end the car or even the system itself is. Before installing a car stereo, make sure that the receiver unit fits into the space you’re installing it in. Most automakers use a standardized size for their factory stereos, including DIN, double-DIN and DIN 1.5. If you have an oversized space, then you will need an adapter plate that provides a sure fit. Wiring the system is another issue that most will run into. Most cars have a factory harness that is incompatible with the connectors on your aftermarket stereo, resulting the need for cutting and rewiring the harness. The use of pre-fabricated wiring harnesses can eliminate the need for cutting and reconnecting wires, not only making the installation much simpler, but also faster.
What is doer and receiver?
In grammar, a doer is the subject of a sentence that performs the action, while the receiver is the object that receives the action. For example, in the sentence "John (doer) gives (action) the book (receiver) to Mary", John is the doer and the book is the receiver.
