0
Why does your car battery spark when you attach the negative cable after you attached the positive first?
Wiki User
∙ 12y ago
A small spark is normal, it is energizing the system.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
How do you hook up jumper cables from one care to another?
To hook up jumper cables, attach one cable from the negative post on one battery to the negative post on the other battery. (These usually are marked "-" and have a blacl cable attached to them.) Attach the other jumper cable from the positive post on one battery to the positive post on the other battery. (These usually are marked "+" and have a red cable attached to them.)
How do you change battery in 2004 gmc sierra?
1. Remove negative battery cable 2. remove positive battery cable 3. remove battery 4. install new battery 5.attach positive cable 6.attach negative cable
Where do the positive and negative wires from the battery attach to the starter on a 1992 F150 six cylinder?
The negative cable actually is bolted to the engine block, and the positive cable will go to the solenoid that is attached to the radiator support. On newer models, the solenoid would be attached to the starter, and then, of course, the positive cable would connect at the solenoid down below on the starter.
How do you charge car battery with solar charger?
Put the solar panel in the sun;Attach the red wire of the panel to the positive terminal of the battery;Attach the black wire of the panel to the negative terminal.
How do you remove the battery from a 2006 BMW 530i?
Disconnect ground. Disconnect positive. Attached chain to back of Semi-Truck, attach chain to battery. Drive the truck away.
What is the procedure of the baterry?
The vehicle battery's main purpose is to supply power for the starting system and to power some accessories when the engine is not running. The proper procedure for changing or installing a battery... remove the battery cable first from the negative battery terminal, then from the positive. Install opposite, attach the positive cable lead, then the negative.
How do you charge the battery on a Chevy hhr?
The battery is located in the cargo area. Access it by removing all of the shrouds as if you were getting to the spare. However there is a jumper/charger terminal under the hood. CAUTION: The fuse box outlet looks a lot like a negative terminal. IT'S NOT! DO NOT attach the negative [black] here. Attach the negative lead [black] to the metal of the engine. Then attach the positive [red] to the positive terminal near the front of the fusebox.
How do you replace a motorcycle battery?
Your battery is dead if it will not accept a charge. Begin by removing the battery cover. Next, remove the negative and positive cables. Lift the battery out of the motorcycle. Replace it with a new battery and attach the negative and positive cables. Turn on the motorcycle to check that the lights are working and start the motorcycle to make sure that it runs properly. Replace the battery cover.
Is positive on a car battery Red or black?
The red jumper cable attaches to the positive end of the battery. Make sure both cars are turned off before attempting to connect the cables and do not touch the metal portions of the cables together or to any part of the car except for the proper battery terminal.You'll first attach the positive (red) cable to the positive terminal of the dead battery. Then attach the other end of the red cable to the positive terminal of the working battery.Then attach the black cable to the negative terminal of the good battery, and finally attach the other end of the black cable to the negative terminal on the dead battery.Make sure everyone is clear of the engine and moving parts before starting the engine of the good car. Allow it to run for a couple of minutes, revving the engine slightly. Then start the engine of the dead car.Be sure to remove the cables in the reverse order of the way you put them on - negative first, then positive.
How do you jump start a Audi q7 battery?
Have someone park their car nose to nose o along side the Audi. With their car running, attach the red clamp to the positive terminal of the Audi battery and the corresponding red clamp to the positive terminal of their carâ??s battery. Then attach the black clamp to the negative terminals on both vehicles.
How do you jump the battery in a 2001 Chrysler sebring convertible?
Under the hood on the driver side are positive and negative jump start posts. The cables attach there.
How do you charge a 2002 BMW 745i battery?
Things You'll NeedCar battery chargero 1 Check that the electrical items in your BMW 328i are turned off and the key is not in the ignition. Open the hood and secure it.o 2 Place your battery charger near the BMW 328i's battery. You need the charger cables to easily reach the car's battery.o 3 Attach the spring clamp on the end of the red cable attached to the battery charger onto the positive terminal of the BMW 328i's battery. The positive terminal is labeled "+" or "Pos."o 4 Attach the spring clamp on the end of the black cable attached to the battery charger onto the negative terminal of the BMW 328i's battery. The negative terminal is labeled "-" or "Neg."o 5 Select the charge setting on your battery charger. If you need to boost your BMW 328i's battery quickly, select the highest charge rate. If you want to charge it slowly -- overnight, for example -- select the lowest charge setting. This setting is often labeled "trickle charge."o 6 Turn on the battery charger. Make sure it is charging at the rate you want. Leave it for several hours, or overnight if on a trickle charge.o 7 Turn off the charger. Remove the black negative cable attached to the charger off the battery's negative terminal. Remove the red positive cable off the battery's positive terminal.o 8 Move the charger away from the BMW 328i. Close the hood.
