0
Why voltage of transformer go up beyond the set voltage when carrying out transformer test?
Wiki User
∙ 12y ago
Transformers without regulators in them will output voltage depending on the voltage coming in.
For instance if you have a 230v to 110v transformer then you will have a ratio of 23:11
this means for every 23 turns in the transformers primary side you will get 11 turns on the secondary, so if you have an input voltage of 247v then the output voltage will be around 118v, conversly if you have an inout voltage of 221v then the ouplut voltage will be around 106v.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Can a high voltage transformer be megged with a megger meter?
No. A megger's output voltage is not high enough to test the insulation of a high-voltage transformer if, by 'high-voltage transformer ', you mean a distribution transformer or power transformer. Instead, a high-voltage test set or 'pressure tester' (e.g. a 'HiPot' tester) must be used, as these produce far higher voltages.
Why instruments are connected on low voltage side of the transformer while performing no load test?
since we need to get desired or rated voltage, so if it is connected in high voltage side of the transformer, voltage supply will be more, and hence the current will be more than the required amount. this is the reason why the instruments re connected at the low voltage of the transformer while performing no load test.
Where is the high side of transformer on open circuit test?
high voltage side call primary
What will happen to the transformer if double the rated voltage is applied to the winding during the open circuit test?
no voltage will be induced on the secondary side of the motor as the windings will become saturated.
Why the iron losses absent in short circuit test?
Because a short-circuit test is done at very low voltage to check the transformer windings on their maximum current. The low voltage ensures that the magnetic flux in the transformer's iron core is very low so that the eddy-current losses, usually known as iron losses, are negligible.
How do you calculate transformer voltage ratio test?
Secondary voltage / primary voltage
Can a high voltage transformer be megged with a megger meter?
No. A megger's output voltage is not high enough to test the insulation of a high-voltage transformer if, by 'high-voltage transformer ', you mean a distribution transformer or power transformer. Instead, a high-voltage test set or 'pressure tester' (e.g. a 'HiPot' tester) must be used, as these produce far higher voltages.
Why instruments are connected on low voltage side of the transformer while performing no load test?
since we need to get desired or rated voltage, so if it is connected in high voltage side of the transformer, voltage supply will be more, and hence the current will be more than the required amount. this is the reason why the instruments re connected at the low voltage of the transformer while performing no load test.
What is power frequency withstand voltage test?
A test done on a transformer. The voltage at the power frequency is ramped up to verify the transformer is capable of handling the stresses due to switching and natural phenomena (lighting strikes).Withstand Voltage:The voltage which has to be applied to a test object under specified conditions in a "withstand test" is called the "withstand voltage".
What are the purposes of performing no load test for the transformer?
These two tests are performed on a transformer to determine (i) equivalent circuit of transformer(ii)voltage regulation of transformer(iii) efficiency of transformer. The power required for theseOpen Circuit test and Short Circuit test on transformeris equal to the power loss occurring in the transformer.
Why open circuit test is done on the transformer with low voltage side shorted?
The supply is given on the high voltage side of transformer because the supply voltage required to circulate rated current through the transformer is usually very small So energy is saved.
Why were instrument of a transformer placed on a high voltage side in short circuit test?
I assume "tension" in this question should be replaced with "voltage". Short circuit tests are often performed from the lower voltage side of the transformer, since a lower voltage source is then required to perform the test. Often times the test lab may not have a source that can output a high enough voltage to perform from the high voltage winding.
Why is a high dc voltage applied to a transformer for testing?
A high dc voltage would be applied to test the insulation between the windings.
Where is the high side of transformer on open circuit test?
high voltage side call primary
What are the types of power transformer test?
open circuit & short circuit test, insulation resistance test, turns ratio, efficiency, if it is oil cooled then breakdown voltage of oil, voltage regulation and definitely visual inpection...
No load current of transformer is non sinusoidal even though sinusoidal voltage is provided in oc sc test?
eddy current loss in the transformer core is reduced by
Why in no load test transformer is connected on low voltage side?
A no-load test is done with the normal supply connected in the way the transformer is intended to be used. It is also known as an open-circuit test to distinguish it from a short-circuit test, and its purpose is to measure the power loss in the iron core of the transformer and the no-load current drawn from the supply.
