0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Mower deck belt installation for a scotts 20 hp 48 inch mower deck?
As your sitting on your mower look down on your left side on the deck is a metal arm locked under a hook get off the mower push down on the arm and pull out toward the rear tire this loosens the rear pulley now put belt over the top front pulley and over the rear pulley move metal arm back to hook and lock in place then your done.
Why does my simplicity riding lawn mower slows down when cutting grass. The grass builds up at the discharge.?
blade needs sharpening,or belt is slipping for mower deck.
How do you remove deck from John Deere lx178?
You first need to set the mower deck setting at high noon to read "blank". More or less between the 1" and 3.5" setting. Then pull deck release arm to allow for the deck to drop to the ground. Once locked into the down position, you need to release the U locks(that are spring loaded) located on the back half, and on both sides of the mower deck. This will allow for the arms that you have unlocked to be retracted up for clearance later. After that you must release the tension bar for the belt pulleys located on top of mower deck, left hand side, and remove the belt connected to the engine pulley located towards the front. After that, you must unlatch the front U-bar from the mower deck. After this is completed. Pull the mower Deck ARM back up, to the position normal for traveling. This will give you clearance to slide the mower deck out from the right side (chute side).
How do you install the mower deck on a LT133 tractor?
The deck must be slipped beneath the machine from the left, the lift lever locked down and the rear hangers and front hanger plate attached. The belt will take take a 90 degree twist with the front part to the left side.
How do i remove and reattach the mower deck on my craftsman riding lawn mower?
park mower on level ground or concrete. lower deck all the way down to ground. lay on your side on the right side of mower. several locking pins need to be pulled out of their slots. lay these to the side and do not misplace them. one cable and washer on top of deck need their locking pin removed. second locking pin needs to be removed from same cable guide way toward rear of deck. this makes 4 pins in all from right side. lay on left side of mower on the ground. three pins on this side need to be remove in same manner. raise height lever all the way back up and this will make it possible to clear mower when you slide deck out from under mower to work on deck . after work is complete, slide deck back under mower as close to location it was in when you started. connect all parts and reinsert pins in reverse order of how you took apart.
How do you know when riding mower deck spindles are bad?
Normally you will start to hear a loud grumbling sound from underneath the mower when the blades are engaged. With the mower shut off, release the tension from the belt for the blades. Raise the deck so you can grab the blades from the bottom. You should not be able to rock the blades from side to side or up and down. If you can then you probably have a bad spindle. You can do this for wach of the spindles to check them all.
Why does my wheel horse mower deck blades slow down when I go into grass?
Maybe you should tighten the drive belt or it could be the PTO clutch is slipping.
How do you level the deck on a john deere lt150 lawn mower?
http://manuals.deere.com/cceomview/OMM143122_E0/Output/Index.html?tM=HO
What could be wrong with my mower when it runs fine but when you turn on deck mower bogs down really bad?
Do your blades spin? Maybe need new belts or something jammed up and when you turn it on, it is straining the engine. Make sure the thing is off and battery disconnected before you start fiddling around under the deck and engine
How do you remove the deck on a john deere lx176?
1. release the tension rod on the left side of the deck and swing it outward 2.on front left axle pull lever out that keeps tension on the u shaped draft bar that hooks into the front of deck and swing it down towards you 3. pull out spring loaded j hooks on each side of rear deck 4. once hooks are released deck will come down,then slide deck out of the discharge side of mower,turning whells to make it easier
How to put belts on yardman riding mower model 13bt604g401?
Park the mower on a level surface preferably concrete apply the park brake and drop the deck to the ground When refered The LHS and RHS of the mower is as you sit on it remove the cutting deck first pull the silver pins at the back of the deck towards you so the rear of the deck is free there is a pin on the lhs and one on the rhs There is a idler bearing adjusting arm on the deck from the lhs pull it toward you this will loosen the belt so it can be removed from the engine pulley There is also a steel rod that may need to be adjusted under the engine pulley it can be adjusted from the rhs by pushing it tward the pulley Then manover the deck forward pushing the front deck locating down then up then slide the deck out to the rhs fit the deck belt as per the manufacturers instruction either on the mower or in your book this belt is different for the 42" and 46" decks Push the seat forward then disconnect the battery and remove the battery box Under the mower on the rhs is a tension spring holding the adjester rod for the upper small belt disconnet it from the chassis by pulling it forward and out remove the small belt through the battery box The main drive belt will be loose to get it off you need to disconnect the electrical plug at the front engine pulley on the rhs and undo the puley bolt from under the mower Reconnect in the reverse order
Why does your Huskee riding mower stalls after engaging blades?
The seat safety switch is not working properly correctly. If the safety does not sense that there is anyone on the seat then it will shut down the mower. This keeps the mower from running over someone if they would happen to fall off while mowing. Or if the safety is working you may have bad bearings on your deck and that will also stall your motor, or something jammed in the blades.
