Plymouth Laser
Honda Civic CX
Scooters and Mini-Bikes

Why would a 1993 Plymouth Laser lose power and misfire at 45mph?

565758

Top Answer
User Avatar
Wiki User
2011-09-13 17:13:43
2011-09-13 17:13:43

If you are blowing any blue smoke or if it rev's really high when u start it for a second or 2 you may have a blown head gasket get that fixed RIGHT AWAY if u you don't you could either crack or worp your head and that's alot more money.......I'd have that checked out

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

A standard green laser pointer has a power of between 4 and 20 milliwatts. A red laser, for comparison, has a power of less than 5 milliwatts. The beam of a green laser can often be seen, while the beam of a red laser cannot be seen.

User Avatar

how do you remove a power steering pump from a 1995 plymouth voyager?

User Avatar

Usually people will choose the most approriate laser pointer to use. It doesn't mean a higher power laser pointer is better than a lower power laser. 5mW laser pointer will be more brighter and visible than a 1mW laser pointer.

User Avatar

Hard start, no start, misfire, back fire, poor fuel economy, low power,Hard start, no start, misfire, back fire, poor fuel economy, low power,

User Avatar

There's no set limit, it depends on the power of the laser and the sensitivity of the receiver.

User Avatar

It all depends on gearing, drag, engine power, but 45mph should be easy

User Avatar

The power steering system on a 2002 Plymouth Voyager uses automatic transmission fluid.

User Avatar

Laser printers can receive too much power from a UPS

User Avatar

cylinux lasers.. it can make the printer. faster and more better.

User Avatar

Economy mode - useful when going over 55mph. It'll help you save gas. Power mode is useful when just cruising around town.

User Avatar

Examples are: A laser is a small light that puts atoms to their highest energy power.

User Avatar

A LASER of sufficient power will vaporize the material where the beam hits it.

User Avatar

Airborne laser is a weapon developed by the US Military with Northrup Grumman. The laser is a high power (in kW region) and can be used to destroy vehicles and personnel.

User Avatar

The power of the engine and the maximum speed of the Plymouth Fury Automatic are 290 horsepower, and 114 mph respectively.

User Avatar

Inkjets normally work on less than 100 watts. Laser printers pull from 400 to 750 watts of power. I've found that laser printers impossible to use when running an ac inverter in my vehicle to power the printer.

User Avatar

Yes.QEP makes a tablesaw with a laser guide.You can also buy attachments for your circular saw

User Avatar

The power of the engine and the maximum speed of the 1971 Plymouth Satellite is 425 hp (317 kW) and 150 mph respectively.

User Avatar

340 V8 bhp is the power of the Plymouth duster manual 1972 engine and its maximum speed is 110 mph.

User Avatar

7. What is output power?The output power is related to the produced power of the laser beam, which is usually stated in milliwatt (mW). The milliwatt is a unit of power, which is one one-thousand of a watt. Higher power lasers are always more powerful than lower power lasers

User Avatar

The 1971 Plymouth duster uses a power steering system ..... Have a good day

User Avatar

The answer is pretty much "No." You can increase the power slightly, but if you go much beyond what it's designed for you'll burn out the laser diode.

User Avatar

Power broadening is an effect whereby the line-width of a laser is broadened by the laser intensity itself. Higher laser intensity leads to a larger line-width. This can be explained by considering the decay rate of atoms from the upper to lower laser level. As the laser intensity increases, this decay rate (which is linearly related to the line-width) increases due to stimulated emission.

User Avatar

Bright, like all laser. It is about as bright as a low power laser pointer. It is usually a class one laser and can not hurt you, but make sure you check it's class before opening the printer, though I would not suggest opening it in the first place.

User Avatar

Laser printers uses dry ink power


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.