Toyota Camry
Ford F-150
Sentence and Word Structure

Why would a 2000 Toyota Camry hesitate when going into reverse?

555657

Top Answer
User Avatar
Wiki User
2004-09-01 10:28:13
2004-09-01 10:28:13

Since it takes more preasure to apply the reverse band, the pump probably has low preasure caused by worn bushings requiring a rebuild.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Probably the electronics going bad.

User Avatar

Replacing the door handle on a 1997 Toyota Camry is easy with the proper tools chief among which is your check book. Start by going to the nearest Toyota dealer. The rest will fall readily into place.

User Avatar

Apperently there are no fuses for the reverse light. First check the wiring that goes down the trunk. The wire tend to split due to the trunk going up and down.

User Avatar

What is your problem. Our 96 Camry measures 1.6 miles for every one mile driven. Coincidence that it's the same measurement as a kilometer? Toyota say yes, but we are going to delve further.

User Avatar

If your engine is a V6 you will have 6 spark plug wires , the engine is V shaped , there will be 3 spark plug wires going to the front and 3 going to the back of the engine : X-----X-----X X-----X-----X front of Toyota Camry If your engine is a 4 cylinder , you will have 4 spark plug wires , the engine will be : X----X----X----X front of Toyota Camry

User Avatar

under the alternator.... the lower hose going to engine

User Avatar

Approximately $1,500 is the going rate for a head gasket replacement.

User Avatar

$200-400 + part price depending on where you are going to fix it.

User Avatar

It sounds like your trainsmission is going bad. something inside the trains- mission. also could be trainsmission vacume line to modual. .

User Avatar

An onboard diagnostic scan would be a good first place to look.

User Avatar

Try going to the junk yards, they always have what you are looking for and at an affordable price.

User Avatar

It's between the transmission and engine bodies, going around the crankshaft.

User Avatar

To turn off the check engine light on a 1999 Toyota Camry you can disconnect the battery. This will only reset the check engine light. So if there is a persistant problem with the engine, the light is likely going to stay on. To turn off the check engine light on a 1999 Toyota Camry you can disconnect the battery. This will only reset the check engine light. So if there is a persistant problem with the engine, the light is likely going to stay on.

User Avatar

If it cranks just fine once it gets going then, most likely, the starter has to be replaced.

User Avatar

Hi, I was looking for instructions as to "How to replace 1998 Toyota Camry rear bumper cover" and you got your question. If you have already replaced then please let me know otherwise I'm going to replace the part this weekened and I will let you know. Take care, Sam

User Avatar

From my knowledge the most common problems with the toyota highlander is visability and speed control.I suggest if you are considering a purchase test these areas while you are going for a test drive.Do things like reverse out of the car yard,drive on a freeway and reverse park.

User Avatar

When you are going to add Freon to a Toyota Camry, you need to know which type to add. You will need to put the Freon recharging coupler to the recharging kit, and get the engine to operating temperature. When the engine is at operating temperature put the air conditioning on the lowest setting and recharge the Freon with the windows of the car rolled down.

User Avatar

It is a large silver cylindrical shaped valve with both A/C lines going to it. Trace your A/C hoses to locate it.

User Avatar

Check the wire which is going inside of the trunk hood to the brake lights.

User Avatar

Only models with v6 have such sensor. If you have one of them, you can find the sensor in the hose coming out of the air filter and going to the injector.

User Avatar

If there is such fuse it should in the main fuse box, in the engine compartment, going along driver's side fender next to the battery.

User Avatar

If you are going to do this job yourself, I would recommend purchasing a shop manual or a Chilton book for that vehicle. It will pay for itself with the first job you do.

User Avatar

You need check that tires are balanced properly. If everything ok with that, your front wheel bearing are going bad.

User Avatar

I've gotten my 4 cylinder engine up to 120mph. The engine does not have enough horsepower to go any faster but the transmission can still keep going.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.