answersLogoWhite
Car Electronics and Lights
Nissan 240SX
Honda Accord LX
MP3 Players Audio and Sound Systems

Why would a newly installed car stereo have power but not have any sound even if the factory model still produces sound on a 95 Nissan 240SX?

484950

Top Answer
User Avatar
Wiki User
2012-03-18 19:07:46
2012-03-18 19:07:46

The car most likely has a built in amp that does not get powered up when you install an aftermarket receiver. Try hooking the blue wire from the car to the blue wire on the receiver harness, usually marked power antena. This sometimes powers the amp. Otherwise if you purchased a wiring harness for your install there's likely a 800# you can call on the pkg. and they can tell you how it's done......good luck

*****************************************************************

I had the same problem with my stereo and I didn't think it could be a wiring issue because i thought i did it all right but it happen to be a wiring. Try disconnecting all the speaker wires and connecting each speaker separately and seeing if it works because that's how I discovered that one of my speakers don't work because of that none of the speakers would play sound. I could also be your ground....

1

Related Questions

User Avatar

go to0 a stereo shop and buy one and have it installed go to0 a stereo shop and buy one and have it installed

User Avatar

color codes for wiring on factory stereo on 2008 Nissan sentra?

User Avatar

The 2002 Nissan Pulsar Factory Stereo wiring diagram can be found in the maintenance manual. It can also be found in the cars repair manual.

User Avatar

When making any electrical changes to the wiring of a car, it is important to have a diagram. A diagram for the factory stereo wiring of a 1993 Nissan Pathfinder can be found in the maintenance manual.

User Avatar

Remove the retaining cover from your factory stereo. Remove the factory stereo retaining bolts. Slide the factory stereo out. Remove the wiring harness and the antenna cable from the back of the factory stereo.

User Avatar

Yes, an amplifier can be installed on a 2000 Chrysler Sebring factory with a CD. Provided the CD drive is working perfectly.?æ

User Avatar

Remove the 2002 Dodge Durango factory stereo decorative cover. Remove the factory stereo retaining screws. Pull the factory stereo out. Remove the wiring harness and the antenna cable from the back of the stereo.

User Avatar

http://www.metraonline.com/downloads/pdf/TurboKits/INST95-7419.pdf

User Avatar

How do you remove stereo from 2000 nissan pathfinder?

User Avatar

no you do not. not even if you have the rockford fosgate package. you just wire up the aftermarket harness(95+ nissan) make sure you connect the blue/white wire. that will turn on the factory amp.

User Avatar

There's 4 holes on the front of the stereo that are used to pull the stereo out. These tools can be purchased at any auto parts store.

User Avatar

AnswerIt's located under the factory stereo in Premium sound models. Here's a link to show you where and how to remove it!Good Luck!-Shaun-

User Avatar

the acutually dash removal of the Comfort-Control Toggle Switch in order to remove facing for radio replacment of 1990 nissan maxima?

User Avatar

you have to remove the front console. take out the ash trey. and remove all the screws around the trim of the area of the stereo and then slid the stereo out and un hook all connections. if you get a new stereo it should have more detailed instructions

User Avatar

If you have the factory installed Monsoon stero, you cannot. Must must but a new stereo that has an audio jack.

User Avatar

How to remove factory stereo from 2001 honda civic?

User Avatar

I just removed my stereo today and installed an aftermarket unit. Use this link for how to remove your factory head unit. http://www.fitaudio.com/?View=entry&EntryID=162

User Avatar

depends on if you have the Bose stereo if you do look under the rear dash in the trunk it would be there

User Avatar

Has it always been like this or not? If it is, then it is not really a problem. It is how the stereo was installed. An stereo can be installed to be turned on whether the engine is on or off. If the stereo cannot be turned off at all, then you have a problem with your stereo.

User Avatar

Check your fuses as this is very common when an after market stereo is installed.

User Avatar

What part is required to connect a mono amp to a factory stereo

User Avatar

Where is factory stereo amp located on a 2007 Cadillac cts

User Avatar

I am trying to install an after market stereo into a 97 Nissan Pickup. I do not know what the wires from the 97 Nissan Pickup do, however, I do know what the wires on the stereo that is to be installed are (i.e. ground = black, yellow = battery). I do not know which wire to attach in aftermarket stereo's wires to in order to make it work and not cause damage to the stereo or the truck.Thank you for your time and consideration. This has been driving me crazy!Cheers-


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.