0
What else can I help you with?
Can use 1A power pack for 500mA device?
Yes, you can use a 1A power pack for a 500mA device. The power pack will supply the necessary 500mA the device requires, with some extra capacity. Ensure that the voltage output matches the device's requirement to avoid any potential damage.
Can 5v 500mA run a 5v 1.8a device?
No, a 5V 500mA power supply cannot run a 5V 1.8A device. The device requires 1.8A of current to operate properly, while the power supply can only provide 0.5A. Attempting to use the lower-rated power supply could result in insufficient power, causing the device to malfunction or not turn on at all.
What will happen if use a 12v 400ma instead of 12v 500ma?
i am not sure, BUT according to the answer in this post:Can_you_use_a_9V_600mA_adapter_on_a_9V_400ma_scanneryou need an adaptor of 9v and AT LEAST 500mA (assuming that the appliance draws 500mA)
Can you use 15v 500ma for a15v 600ma?
Yes, you can use a 15V power supply rated for 500mA with a device that requires 15V and 600mA, but it may not function properly. The power supply will likely not provide enough current to meet the device's needs, which could lead to underperformance or potential damage to the power supply. It's always best to use a power supply that matches or exceeds the required current rating for optimal performance and safety.
Can you use 12v 600ma instead of 12v 500ma?
Using a 12v 600ma source is allowing 12 volts and 600 amps of power. If the device requires a 12v 500ma source, the larger source is acceptable. Please note that it will only be drawing on 500ma of the available 600ma.
What will happen if use a 12v 500ma instead of 12v 300ma?
Using a 12V 500mA power supply instead of a 12V 300mA power supply will likely be fine as long as the voltage matches, but the higher current capacity (500mA) means the power supply can deliver more current if needed by the device. The device will only draw the current it needs, so having a higher current capacity power supply should not cause any issues.
Can you use 500MA instead of 1Amp?
Yes, you can use a 500mA (0.5A) supply instead of a 1A supply, but it depends on the requirements of your device. If the device draws more than 500mA, it may not function properly or could be damaged due to insufficient current. Always ensure that the power supply can meet the current demands of your application for safe and effective operation.
Is 9vdc 500ma the same as 9vdc 1.5a?
No, 9VDC 500mA is not the same as 9VDC 1.5A. While both have the same voltage of 9 volts, they differ in current capacity; 500mA (0.5A) means the device can draw a maximum of 500 milliamps, while 1.5A allows for a maximum of 1,500 milliamps. Therefore, a 9VDC 1.5A power supply can provide more current than a 9VDC 500mA supply, which is important for devices that require higher power. Always match the power supply specifications with the device requirements to avoid damage.
What device requires an electric power supply?
A motor
Can you use a 9v 1500ma on 9v 500ma device?
Yes. (For any pairing of power supply and device, as long as the voltages are a match (in your case: 9v), and the output (in amps or milliamps (A or mA) of the power supply IS EQUAL TO OR GREATER THAN the current required by the device (in your case 1300mA or higher) then you will be fine. Yes it is suitable: The OUTPUT VOLTAGE (5v, 9v, 12v, etc) of a power supply MUST BE EQUIVALENT to the required voltage of the device to which it is to be connected, whereas the output CURRENT (500mA, 1A, 1500mA, 2A... etc) offered by the power supply MUST BE AT LEAST EQUAL TO OR GREATER THAN the current required by the device to which it is to be connected. (in your case, for example, as long as the power supply is rated at 9v, you could use one that has a rating of 1300mA, 1400mA, 1500mA, 1A...and so-on, without any damage to either device)
Can a 12v dc 500mA adapter be substituted for a 12v dc 200mA ac adapter?
No.If it is AC output, it will blow out the power circuits of the DC device.If it is DC output, it doesn't have enough current capacity for the load of the DC device.If you want to power a DC device with a wall wart, make sure the wart is:DC outputCorrect polarity (some have reversible polarity)Exact same voltage as the deviceGreater than or equal to current rating of the device
Can you use a 12vac 1amp power supply on a device that requires 15vac 130mA?
No, you cannot.
